Remove unnecessary tabs and spaces

Marlin/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -827,10 +827,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/M100_Free_Mem_Chk.cpp

@@ -22,10 +22,10 @@
 
 /**
  * M100 Free Memory Watcher
- * 
+ *
  * This code watches the free memory block between the bottom of the heap and the top of the stack.
  * This memory block is initialized and watched via the M100 command.
- * 
+ *
  * M100 I Initializes the free memory block and prints vitals statistics about the area
  * M100 F Identifies how much of the free memory block remains free and unused.  It also
  *    detects and reports any corruption within the free memory block that may have
@@ -34,7 +34,7 @@
  *    data that does not match the expected value.
  * M100 C x Corrupts x locations within the free memory block.   This is useful to check the
  *    correctness of the M100 F and M100 D commands.
- * 
+ *
  * Initial version by Roxy-3DPrintBoard
  */
 #define M100_FREE_MEMORY_DUMPER     // Comment out to remove Dump sub-command

Marlin/Marlin_main.cpp

@@ -5259,7 +5259,7 @@ inline void gcode_M104() {
 
     if (code_value_temp_abs() > thermalManager.degHotend(target_extruder)) LCD_MESSAGEPGM(MSG_HEATING);
   }
-  
+
   #if ENABLED(AUTOTEMP)
     planner.autotemp_M104_M109();
   #endif

Marlin/endstops.cpp

@@ -255,14 +255,14 @@ void Endstops::update() {
       } \
     } while(0)
 
-  #if ENABLED(G38_PROBE_TARGET) && PIN_EXISTS(Z_MIN)  // If G38 command then check Z_MIN for every axis and every direction  
+  #if ENABLED(G38_PROBE_TARGET) && PIN_EXISTS(Z_MIN)  // If G38 command then check Z_MIN for every axis and every direction
 
     #define UPDATE_ENDSTOP(AXIS,MINMAX) do { \
         _UPDATE_ENDSTOP(AXIS,MINMAX,NOOP); \
         if (G38_move) _UPDATE_ENDSTOP(Z, MIN, G38_endstop_hit = true); \
       } while(0)
 
-  #else	
+  #else
 
     #define UPDATE_ENDSTOP(AXIS,MINMAX) _UPDATE_ENDSTOP(AXIS,MINMAX,NOOP)
 

Marlin/example_configurations/Cartesio/Configuration.h

@@ -207,7 +207,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -232,13 +232,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -827,10 +827,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/Felix/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -810,10 +810,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -810,10 +810,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/Hephestos/Configuration.h

@@ -209,7 +209,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -234,13 +234,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -819,10 +819,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/K8200/Configuration.h

@@ -226,7 +226,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -251,13 +251,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -856,10 +856,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -481,12 +481,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/K8400/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -827,10 +827,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/K8400/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/K8400/Dual-head/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -827,10 +827,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -827,10 +827,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/RigidBot/Configuration.h

@@ -209,7 +209,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -234,13 +234,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -826,10 +826,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/SCARA/Configuration.h

@@ -238,7 +238,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -263,13 +263,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -842,10 +842,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/TAZ4/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -848,10 +848,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/TAZ4/Configuration_adv.h

@@ -476,12 +476,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/WITBOX/Configuration.h

@@ -209,7 +209,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -234,13 +234,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -819,10 +819,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -827,10 +827,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -921,10 +921,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/delta/biv2.5/Configuration_adv.h

@@ -470,12 +470,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/delta/generic/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -915,10 +915,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -470,12 +470,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -918,10 +918,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -470,12 +470,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -210,7 +210,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -235,13 +235,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -917,10 +917,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -475,12 +475,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -199,7 +199,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -224,13 +224,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -921,10 +921,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -470,12 +470,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/makibox/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -830,10 +830,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -206,7 +206,7 @@
 
 /**
  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- * 
+ *
  * Temperature sensors available:
  *
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
@@ -231,13 +231,13 @@
  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  *    66 : 4.7M High Temperature thermistor from Dyze Design
  *    70 : the 100K thermistor found in the bq Hephestos 2
- * 
+ *
  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  *                              (but gives greater accuracy and more stable PID)
  *    51 : 100k thermistor - EPCOS (1k pullup)
  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- * 
+ *
  *  1047 : Pt1000 with 4k7 pullup
  *  1010 : Pt1000 with 1k pullup (non standard)
  *   147 : Pt100 with 4k7 pullup
@@ -823,10 +823,10 @@
     // The height can be set with M420 Z<height>
     #define ENABLE_LEVELING_FADE_HEIGHT
 
-    // 
+    //
     // Experimental Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
-    // 
+    //
     //#define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -468,12 +468,12 @@
 
 /**
  * Additional options for Graphical Displays
- * 
+ *
  * Use the optimizations here to improve printing performance,
  * which can be adversely affected by graphical display drawing,
  * especially when doing several short moves, and when printing
  * on DELTA and SCARA machines.
- * 
+ *
  * Some of these options may result in the display lagging behind
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.

Marlin/language_tr.h

@@ -57,12 +57,12 @@
 #define MSG_HOME_OFFSETS_APPLIED            _UxGT("Offset Tamam")                                       // Offset Tamam
 #define MSG_SET_ORIGIN                      _UxGT("Sıfır Belirle")                                      // Sıfır Belirle
 #define MSG_PREHEAT_1                       _UxGT("Ön Isınma PLA")                                      // Ön Isınma PLA
-#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 _UxGT(" ")                                    //  
+#define MSG_PREHEAT_1_N                     MSG_PREHEAT_1 _UxGT(" ")                                    //
 #define MSG_PREHEAT_1_ALL                   MSG_PREHEAT_1 _UxGT(" Tüm")                                 //  Tüm
 #define MSG_PREHEAT_1_BEDONLY               MSG_PREHEAT_1 _UxGT(" Tabla")                               //  Tabla
 #define MSG_PREHEAT_1_SETTINGS              MSG_PREHEAT_1 _UxGT(" Ayar")                                //  Ayar
 #define MSG_PREHEAT_2                       _UxGT("Ön Isınma ABS")                                      // Ön Isınma ABS
-#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 _UxGT(" ")                                    //  
+#define MSG_PREHEAT_2_N                     MSG_PREHEAT_2 _UxGT(" ")                                    //
 #define MSG_PREHEAT_2_ALL                   MSG_PREHEAT_2 _UxGT(" Tüm")                                 //  Tüm
 #define MSG_PREHEAT_2_BEDONLY               MSG_PREHEAT_2 _UxGT(" Tabla")                               //  Tabla
 #define MSG_PREHEAT_2_SETTINGS              MSG_PREHEAT_2 _UxGT(" Ayar")                                //  Ayar
@@ -91,7 +91,7 @@
 #define MSG_MAX                             _UxGT(" ") LCD_STR_THERMOMETER _UxGT(" Max")                //  Max
 #define MSG_FACTOR                          _UxGT(" ") LCD_STR_THERMOMETER _UxGT(" Çarpan")             //  Çarpan
 #define MSG_AUTOTEMP                        _UxGT("Autotemp")                                           //  Autotemp
-#define MSG_ON                              _UxGT("On ")                                                // On 
+#define MSG_ON                              _UxGT("On ")                                                // On
 #define MSG_OFF                             _UxGT("Off")                                                // Off
 #define MSG_PID_P                           _UxGT("PID-P")                                              // PID-P
 #define MSG_PID_I                           _UxGT("PID-I")                                              // PID-I

Marlin/pins.h

@@ -135,7 +135,7 @@
   #include "pins_MEGATRONICS_3.h"
 #elif MB(MEGATRONICS_31)
   #define MEGATRONICS_31
-  #include "pins_MEGATRONICS_3.h" 
+  #include "pins_MEGATRONICS_3.h"
 #elif MB(OMCA_A)
   #include "pins_OMCA_A.h"
 #elif MB(OMCA)

Marlin/pins_MEGATRONICS_3.h

@@ -153,7 +153,7 @@
   #define LCD_PINS_D5      30
   #define LCD_PINS_D6      39
   #define LCD_PINS_D7      15
-  
+
   #define SHIFT_CLK        43
   #define SHIFT_LD         35
   #define SHIFT_OUT        34

Marlin/pins_RIGIDBOARD_V2.h

@@ -39,7 +39,7 @@
 
 #define DAC_STEPPER_SENSE    0.05 // sense resistors on rigidboard stepper chips are .05 value
 #define DAC_STEPPER_ADDRESS  0
-#define DAC_STEPPER_MAX   4096 // was 5000 but max allowable value is actually 4096 
+#define DAC_STEPPER_MAX   4096 // was 5000 but max allowable value is actually 4096
 #define DAC_STEPPER_VREF     1 // internal Vref, gain 2x = 4.096V
 #define DAC_STEPPER_GAIN     1 // value of 1 here sets gain of 2
 #define DAC_DISABLE_PIN     42 // set low to enable DAC

Marlin/planner.cpp

@@ -675,7 +675,7 @@ void Planner::_buffer_line(const float &a, const float &b, const float &c, const
     const float target_float[XYZE] = { a, b, c, e },
                 de_float = target_float[E_AXIS] - position_float[E_AXIS],
                 mm_D_float = sqrt(sq(target_float[X_AXIS] - position_float[X_AXIS]) + sq(target_float[Y_AXIS] - position_float[Y_AXIS]));
-    
+
     memcpy(position_float, target_float, sizeof(position_float));
   #endif
 
@@ -1108,7 +1108,7 @@ void Planner::_buffer_line(const float &a, const float &b, const float &c, const
         if (accel * block->steps[AXIS] > comp) accel = comp / block->steps[AXIS]; \
       } \
     }while(0)
-	
+
     #define LIMIT_ACCEL_FLOAT(AXIS,INDX) do{ \
       if (block->steps[AXIS] && max_acceleration_steps_per_s2[AXIS+INDX] < accel) { \
         const float comp = (float)max_acceleration_steps_per_s2[AXIS+INDX] * (float)block->step_event_count; \
@@ -1292,11 +1292,11 @@ void Planner::_buffer_line(const float &a, const float &b, const float &c, const
     // Use LIN_ADVANCE for blocks if all these are true:
     //
     // esteps                                          : We have E steps todo (a printing move)
-    // 
+    //
     // block->steps[X_AXIS] || block->steps[Y_AXIS]    : We have a movement in XY direction (i.e., not retract / prime).
-    // 
+    //
     // extruder_advance_k                              : There is an advance factor set.
-    // 
+    //
     // block->steps[E_AXIS] != block->step_event_count : A problem occurs if the move before a retract is too small.
     //                                                   In that case, the retract and move will be executed together.
     //                                                   This leads to too many advance steps due to a huge e_acceleration.

Marlin/planner.h

@@ -123,7 +123,7 @@ typedef struct {
   #if ENABLED(BARICUDA)
     uint32_t valve_pressure, e_to_p_pressure;
   #endif
-  
+
   uint32_t segment_time;
 
 } block_t;
@@ -185,7 +185,7 @@ class Planner {
      * Nominal speed of previous path line segment
      */
     static float previous_nominal_speed;
-	
+
     /**
      * Limit where 64bit math is necessary for acceleration calculation
      */
@@ -206,7 +206,7 @@ class Planner {
       // Segment times (in µs). Used for speed calculations
       static long axis_segment_time[2][3];
     #endif
-    
+
     #if ENABLED(LIN_ADVANCE)
       static float position_float[NUM_AXIS];
       static float extruder_advance_k;
@@ -264,7 +264,7 @@ class Planner {
       #define ARG_Z const float &lz
 
     #endif
-    
+
     #if ENABLED(LIN_ADVANCE)
       void advance_M905(const float &k);
     #endif

Marlin/stepper.cpp

@@ -338,7 +338,7 @@ void Stepper::isr() {
   CBI(TIMSK0, OCIE0B); //Temperature ISR
   DISABLE_STEPPER_DRIVER_INTERRUPT();
   sei();
-  
+
   if (cleaning_buffer_counter) {
     --cleaning_buffer_counter;
     current_block = NULL;
@@ -583,7 +583,7 @@ void Stepper::isr() {
       #endif
    }
   #endif
-  
+
   #if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
     // If we have esteps to execute, fire the next advance_isr "now"
     if (e_steps[TOOL_E_INDEX]) OCR0A = TCNT0 + 2;

Marlin/stepper.h

@@ -358,7 +358,7 @@ class Stepper {
       acc_step_rate = current_block->initial_rate;
       acceleration_time = calc_timer(acc_step_rate);
       OCR1A = acceleration_time;
-      
+
       #if ENABLED(LIN_ADVANCE)
         if (current_block->use_advance_lead) {
           current_estep_rate[current_block->active_extruder] = ((unsigned long)acc_step_rate * current_block->abs_adv_steps_multiplier8) >> 17;

Marlin/stepper_dac.cpp

@@ -88,7 +88,7 @@
 
   static float dac_perc(int8_t n) { return 100.0 * mcp4728_getValue(dac_order[n]) * (1.0 / (DAC_STEPPER_MAX)); }
   static float dac_amps(int8_t n) { return mcp4728_getDrvPct(dac_order[n]) * (DAC_STEPPER_MAX) * 0.125 * (1.0 / (DAC_STEPPER_SENSE)); }
-  
+
   int16_t dac_current_get_percent(AxisEnum axis) { return mcp4728_getDrvPct(dac_order[axis]); }
   void dac_current_set_percents(int16_t pct[XYZE]) {
     LOOP_XYZE(i) dac_channel_pct[i] = pct[dac_order[i]];
@@ -101,7 +101,7 @@
     SERIAL_ECHO_START;
     SERIAL_ECHOLNPGM("Stepper current values in % (Amps):");
     SERIAL_ECHO_START;
-    SERIAL_ECHOPAIR(" X:",  dac_perc(X_AXIS)); 
+    SERIAL_ECHOPAIR(" X:",  dac_perc(X_AXIS));
     SERIAL_ECHOPAIR(" (",   dac_amps(X_AXIS));
     SERIAL_ECHOPAIR(") Y:", dac_perc(Y_AXIS));
     SERIAL_ECHOPAIR(" (",   dac_amps(Y_AXIS));

Marlin/temperature.cpp

@@ -1943,6 +1943,6 @@ void Temperature::isr() {
       if (!endstop_monitor_count) endstop_monitor();  // report changes in endstop status
     }
   #endif
-  
+
   SBI(TIMSK0, OCIE0B); //re-enable Temperature ISR
 }