Back port Cosmetic changes

Marlin/example_configurations/Felix/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/Felix/Configuration_DUAL.h

 //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
 #if ENABLED(PIDTEMPBED)
-// Felix Foil Heater
-   #define DEFAULT_bedKp 103.37
-   #define DEFAULT_bedKi 2.79
-   #define DEFAULT_bedKd 956.94
+  // Felix Foil Heater
+  #define DEFAULT_bedKp 103.37
+  #define DEFAULT_bedKi 2.79
+  #define DEFAULT_bedKd 956.94
 
 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/Hephestos/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/K8200/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/RigidBot/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/SCARA/Configuration.h

   // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
   //#define ENDSTOPPULLUP_XMAX
   //#define ENDSTOPPULLUP_YMAX
-   #define ENDSTOPPULLUP_ZMAX  // open pin, inverted
-   #define ENDSTOPPULLUP_XMIN  // open pin, inverted
-   #define ENDSTOPPULLUP_YMIN  // open pin, inverted
+  #define ENDSTOPPULLUP_ZMAX  // open pin, inverted
+  #define ENDSTOPPULLUP_XMIN  // open pin, inverted
+  #define ENDSTOPPULLUP_YMIN  // open pin, inverted
   //#define ENDSTOPPULLUP_ZMIN
   //#define ENDSTOPPULLUP_ZMIN_PROBE
 #endif
 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
- //#define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
-                          // When defined, it will:
-                          // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
-                          // - If stepper drivers timeout, it will need X and Y homing again before Z homing.
-                          // - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28).
-                          // - Block Z homing only when the Z probe is outside bed area.
+  //#define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
+                            // When defined, it will:
+                            // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
+                            // - If stepper drivers timeout, it will need X and Y homing again before Z homing.
+                            // - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28).
+                            // - Block Z homing only when the Z probe is outside bed area.
 
   #if ENABLED(Z_SAFE_HOMING)
 

Marlin/example_configurations/TAZ4/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/WITBOX/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/adafruit/ST7565/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/delta/biv2.5/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 50    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
     #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
   #endif
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/delta/generic/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 50    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
     //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
   #endif
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/delta/kossel_mini/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 50    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
     //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
   #endif
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/delta/kossel_pro/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
     #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
   #endif
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/makibox/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will:

Marlin/example_configurations/tvrrug/Round2/Configuration.h

 
   #else  // !AUTO_BED_LEVELING_GRID
 
-      // Arbitrary points to probe.
-      // A simple cross-product is used to estimate the plane of the bed.
-      #define ABL_PROBE_PT_1_X 15
-      #define ABL_PROBE_PT_1_Y 180
-      #define ABL_PROBE_PT_2_X 15
-      #define ABL_PROBE_PT_2_Y 20
-      #define ABL_PROBE_PT_3_X 170
-      #define ABL_PROBE_PT_3_Y 20
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
 
   #endif // AUTO_BED_LEVELING_GRID
 
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
   #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
-                                                                            // Useful to retract a deployable Z probe.
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
 
   //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
   //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-// If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
-// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
+  // If you have enabled the bed auto leveling and are using the same Z probe for Z homing,
+  // it is highly recommended you let this Z_SAFE_HOMING enabled!!!
 
   #define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with Z probe outside the bed area.
                           // When defined, it will: