Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface

Marlin/Configuration.h

 // Ultimaker = 7,
 // Teensylu = 8,
 // Gen3+ =9
-#define MOTHERBOARD 7
+#define MOTHERBOARD 33
 
 //===========================================================================
 //=============================Thermal Settings  ============================
 // 6 is EPCOS 100k
 // 7 is 100k Honeywell thermistor 135-104LAG-J01
 
-#define TEMP_SENSOR_0 -1
+#define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 
 // Actual temperature must be close to target for this long before M109 returns success
-#define TEMP_RESIDENCY_TIME 30  // (seconds)
+#define TEMP_RESIDENCY_TIME 10	// 30  // (seconds) 30 seconds was too long
 #define TEMP_HYSTERESIS 3       // (C°) range of +/- temperatures considered "close" to the target one
 
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
 //can be software-disabled for whatever purposes by
 #define PREVENT_DANGEROUS_EXTRUDE
-#define EXTRUDE_MINTEMP 190
+#define EXTRUDE_MINTEMP 170		// 190 //  Lowered a bit as I want to print PLA
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
 //===========================================================================
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
 // The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
-const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
-const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
-const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
+const bool X_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops. 
+const bool Y_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops. 
+const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops. 
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 #define X_ENABLE_ON 0
 #define DISABLE_Z false
 #define DISABLE_E false // For all extruders
 
-#define INVERT_X_DIR true    // for Mendel set to false, for Orca set to true
-#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR true    // for Mendel set to true, for Orca set to false
 #define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
 #define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
 #define INVERT_E1_DIR false    // for direct drive extruder v9 set to true, for geared extruder set to false
 
 #define min_software_endstops true //If true, axis won't move to coordinates less than zero.
 #define max_software_endstops true  //If true, axis won't move to coordinates greater than the defined lengths below.
-#define X_MAX_LENGTH 205
-#define Y_MAX_LENGTH 205
-#define Z_MAX_LENGTH 200
+#define X_MAX_LENGTH 175
+#define Y_MAX_LENGTH 185
+#define Z_MAX_LENGTH 90
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
-#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0}  // set the homing speeds (mm/min)
+#define HOMING_FEEDRATE {1500, 1500, 80, 0} // {50*60, 50*60, 4*60, 0}  // set the homing speeds (mm/min)
 
 // default settings 
 
-#define DEFAULT_AXIS_STEPS_PER_UNIT   {78.7402,78.7402,200*8/3,760*1.1}                    // default steps per unit for ultimaker 
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {80, 80, 2560,640.15}	// {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for metric prusa 
 #define DEFAULT_MAX_FEEDRATE          {500, 500, 5, 45}    // (mm/sec)    
 #define DEFAULT_MAX_ACCELERATION      {9000,9000,100,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
 
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves 
-#define DEFAULT_RETRACT_ACCELERATION  3000   // X, Y, Z and E max acceleration in mm/s^2 for r retracts
+#define DEFAULT_ACCELERATION          1500	// 3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves 
+#define DEFAULT_RETRACT_ACCELERATION  1500	// 3000   // X, Y, Z and E max acceleration in mm/s^2 for r retracts
 
 // 
 #define DEFAULT_XYJERK                20.0    // (mm/sec)
 //#define ULTRA_LCD  //general lcd support, also 16x2
 #define SDSUPPORT // Enable SD Card Support in Hardware Console
 
-//#define ULTIPANEL
+#define ULTIPANEL
 #ifdef ULTIPANEL
-  //#define NEWPANEL  //enable this if you have a click-encoder panel
+  #define NEWPANEL  //enable this if you have a click-encoder panel
   #define SDSUPPORT
   #define ULTRA_LCD
   #define LCD_WIDTH 20

Marlin/pins.h

 #define SDPOWER            -1
 #define SDSS               53
 #define LED_PIN            13
-#define FAN_PIN            4
+#define FAN_PIN            9 // Uses HEATER_1 on Ramps Board
 #define PS_ON_PIN          12
 #define KILL_PIN           -1
 
 #define HEATER_BED_PIN     8    // BED
 #define TEMP_BED_PIN       14   // ANALOG NUMBERING
 
+#ifdef ULTRA_LCD
+
+  #ifdef NEWPANEL
+  //arduino pin witch triggers an piezzo beeper
+    #define BEEPER -1			// No Beeper added
+
+    #define LCD_PINS_RS 16 
+    #define LCD_PINS_ENABLE 17
+    #define LCD_PINS_D4 23
+    #define LCD_PINS_D5 25 
+    #define LCD_PINS_D6 27
+    #define LCD_PINS_D7 29
+    
+    //buttons are directly attached using AUX-2
+    #define BTN_EN1 44
+    #define BTN_EN2 42
+    #define BTN_ENC 64  //the click
+    
+    #define BLEN_C 2
+    #define BLEN_B 1
+    #define BLEN_A 0
+    
+    #define SDCARDDETECT -1		// Ramps does not use this port
+    
+      //encoder rotation values
+    #define encrot0 0
+    #define encrot1 2
+    #define encrot2 3
+    #define encrot3 1
+
+  #else //old style panel with shift register
+    //arduino pin witch triggers an piezzo beeper
+    #define BEEPER -1		No Beeper added
+
+    //buttons are attached to a shift register
+	// Not wired this yet
+    //#define SHIFT_CLK 38
+    //#define SHIFT_LD 42
+    //#define SHIFT_OUT 40
+    //#define SHIFT_EN 17
+    
+    #define LCD_PINS_RS 16 
+    #define LCD_PINS_ENABLE 17
+    #define LCD_PINS_D4 23
+    #define LCD_PINS_D5 25 
+    #define LCD_PINS_D6 27
+    #define LCD_PINS_D7 29
+    
+    //encoder rotation values
+    #define encrot0 0
+    #define encrot1 2
+    #define encrot2 3
+    #define encrot3 1
+
+    
+    //bits in the shift register that carry the buttons for:
+    // left up center down right red
+    #define BL_LE 7
+    #define BL_UP 6
+    #define BL_MI 5
+    #define BL_DW 4
+    #define BL_RI 3
+    #define BL_ST 2
+
+    #define BLEN_B 1
+    #define BLEN_A 0
+  #endif 
+#endif //ULTRA_LCD
 
 #else // RAMPS_V_1_1 or RAMPS_V_1_2 as default