Add missing CHAMBER options (for M141) (#13371)

Marlin/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/default/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/3DFabXYZ/Migbot/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/AlephObjects/TAZ4/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 250
 #define HEATER_5_MAXTEMP 250
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/AliExpress/CL-260/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/AliExpress/UM2pExt/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      130
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Anet/A2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Anet/A2plus/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Anet/A6/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      130
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Anet/A8/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      130
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/AnyCubic/i3/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/ArmEd/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Azteeg/X5GT/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/BIBO/TouchX/cyclops/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      115
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/BIBO/TouchX/default/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      115
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/BQ/Hephestos/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 260
 #define HEATER_5_MAXTEMP 260
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/BQ/Hephestos_2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      100
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/BQ/WITBOX/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 260
 #define HEATER_5_MAXTEMP 260
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Cartesio/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 415
 #define HEATER_5_MAXTEMP 415
 #define BED_MAXTEMP      165
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/CR-10/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/CR-10S/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/CR-10_5S/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/CR-10mini/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/CR-8/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/Ender-2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP       75
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/Ender-3/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      125
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Creality/Ender-4/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Einstart-S/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Felix/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Felix/DUAL/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/FlashForge/CreatorPro/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/FolgerTech/i3-2020/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 245
 #define HEATER_5_MAXTEMP 245
 #define BED_MAXTEMP      115
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Formbot/Raptor/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_3_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_3_MAXTEMP 275
 #define HEATER_4_MAXTEMP 275
 #if ENABLED(BED_AC)
-  #define BED_MAXTEMP      150
+  #define BED_MAXTEMP    150
 #else
-  #define BED_MAXTEMP      100
+  #define BED_MAXTEMP    100
 #endif
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Formbot/T_Rex_2+/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Formbot/T_Rex_3/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/A10M/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/A20M/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/GT2560/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/MeCreator2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      125
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      125
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Infitary/i3-M508/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      125
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/JGAurora/A5/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/MakerParts/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Malyan/M150/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Malyan/M200/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      100
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Micromake/C1/basic/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Micromake/C1/enhanced/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Mks/Robin/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Mks/Sbase/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Printrbot/PrintrboardG2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/RapideLite/RL200/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 250
 #define HEATER_5_MAXTEMP 250
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/RepRapPro/Huxley/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/RepRapWorld/Megatronics/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/RigidBot/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/SCARA/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/STM32F10/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/STM32F4/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Sanguinololu/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/TheBorg/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/TinyBoy2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      100
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Tronxy/X1/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 260
 #define HEATER_5_MAXTEMP 260
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Tronxy/X3A/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      130
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Tronxy/X5S-2E/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 // Tronxy X5S-2E:
 // The OEM stock model uses a clone MK3a 300 @ 12V with no insulation and can reach a maximum 70C at 25C ambient.
 #define BED_MAXTEMP       81
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Tronxy/X5S/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Tronxy/XY100/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/UltiMachine/Archim1/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/UltiMachine/Archim2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/VORONDesign/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Velleman/K8200/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Velleman/K8400/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Velleman/K8400/Dual-head/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/WASP/PowerWASP/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/Wanhao/Duplicator 6/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/adafruit/ST7565/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/Anycubic/Kossel/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/FLSUN/auto_calibrate/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 250
 #define HEATER_5_MAXTEMP 250
 #define BED_MAXTEMP      115
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/FLSUN/kossel/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 250
 #define HEATER_5_MAXTEMP 250
 #define BED_MAXTEMP      115
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/FLSUN/kossel_mini/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/Geeetech/Rostock 301/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/Hatchbox_Alpha/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/MKS/SBASE/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/Tevo Little Monster/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/generic/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/kossel_mini/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/kossel_pro/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/delta/kossel_xl/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/gCreate/gMax1.5+/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 245
 #define HEATER_5_MAXTEMP 245
 #define BED_MAXTEMP      115
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/makibox/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/stm32f103ret6/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/tvrrug/Round2/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================

config/examples/wt150/Configuration.h

 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   5
 #define HEATER_4_MINTEMP   5
 #define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 #define HEATER_4_MAXTEMP 275
 #define HEATER_5_MAXTEMP 275
 #define BED_MAXTEMP      150
+#define CHAMBER_MAXTEMP  100
 
 //===========================================================================
 //============================= PID Settings ================================