Merge pull request #10173 from noingwhat/2.0.x-Continuous-Purge

[2.0.x] Continuous Purge

.travis.yml

   #      ULTIMAKERCONTROLLER, FILAMENT_LCD_DISPLAY, FILAMENT_WIDTH_SENSOR,
   #      PRINTCOUNTER, NOZZLE_PARK_FEATURE, NOZZLE_CLEAN_FEATURE, PCA9632,
   #      Z_DUAL_STEPPER_DRIVERS, Z_DUAL_ENDSTOPS, BEZIER_CURVE_SUPPORT, EXPERIMENTAL_I2CBUS,
-  #      ADVANCED_PAUSE_FEATURE, PARK_HEAD_ON_PAUSE, LCD_INFO_MENU,
+  #      ADVANCED_PAUSE_FEATURE, ADVANCED_PAUSE_CONTINUOUS_PURGE, PARK_HEAD_ON_PAUSE, LCD_INFO_MENU,
   #      EEPROM_SETTINGS, EEPROM_CHITCHAT, M100_FREE_MEMORY_WATCHER,
   #      INCH_MODE_SUPPORT, TEMPERATURE_UNITS_SUPPORT
   #
   - opt_enable ULTIMAKERCONTROLLER SDSUPPORT
   - opt_enable PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE PCA9632 USE_XMAX_PLUG
   - opt_enable_adv BEZIER_CURVE_SUPPORT EXPERIMENTAL_I2CBUS
-  - opt_enable_adv ADVANCED_PAUSE_FEATURE FILAMENT_LOAD_UNLOAD_GCODES PARK_HEAD_ON_PAUSE LCD_INFO_MENU M114_DETAIL
+  - opt_enable_adv ADVANCED_PAUSE_FEATURE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES PARK_HEAD_ON_PAUSE LCD_INFO_MENU M114_DETAIL
   - opt_set_adv PWM_MOTOR_CURRENT {1300,1300,1250}
   - opt_set_adv I2C_SLAVE_ADDRESS 63
   - build_marlin_pio ${TRAVIS_BUILD_DIR} ${TEST_PLATFORM}

Marlin/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/default/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Cartesio/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 120       // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 6       // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 120       // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 6       // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Felix/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 6       // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/MakerParts/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/RigidBot/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/SCARA/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/TheBorg/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/delta/generic/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/makibox/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/config/examples/wt150/Configuration_adv.h

   #define FILAMENT_UNLOAD_RETRACT_LENGTH 13   // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY 5000          // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH 8      // (mm) An unretract is done, then this length is purged.
+  //#define ADVANCED_PAUSE_CONTINUOUS_PURGE   // Purge continuously up to the purge length until interrupted.
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT 45        // (seconds) Time limit before the nozzle is turned off for safety.
   #define FILAMENT_CHANGE_ALERT_BEEPS 10      // Number of alert beeps to play when a response is needed.

Marlin/src/feature/pause.cpp

   // Load filament
   if (load_length) do_pause_e_move(load_length, FILAMENT_CHANGE_LOAD_FEEDRATE);
 
-  do {
-    if (purge_length > 0) {
-      // "Wait for filament purge"
-      #if ENABLED(ULTIPANEL)
-        if (show_lcd)
-          lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_PURGE, mode);
-      #endif
-
-      // Extrude filament to get into hotend
-      do_pause_e_move(purge_length, ADVANCED_PAUSE_EXTRUDE_FEEDRATE);
-    }
+  #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
 
-    // Show "Purge More" / "Resume" menu and wait for reply
     #if ENABLED(ULTIPANEL)
-      if (show_lcd) {
-        KEEPALIVE_STATE(PAUSED_FOR_USER);
-        wait_for_user = false;
-        lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_OPTION, mode);
-        while (advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_WAIT_FOR) idle(true);
-        KEEPALIVE_STATE(IN_HANDLER);
-      }
+      if (show_lcd)
+        lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_CONTINUOUS_PURGE);
     #endif
 
-    // Keep looping if "Purge More" was selected
-  } while (
-    #if ENABLED(ULTIPANEL)
-      show_lcd && advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_EXTRUDE_MORE
-    #else
-      0
-    #endif
-  );
+    wait_for_user = true;
+    for (float purge_count = purge_length; purge_count > 0 && wait_for_user; --purge_count)
+      do_pause_e_move(1, ADVANCED_PAUSE_EXTRUDE_FEEDRATE);
+    wait_for_user = false;
+
+  #else
+
+    do {
+      if (purge_length > 0) {
+        // "Wait for filament purge"
+        #if ENABLED(ULTIPANEL)
+          if (show_lcd)
+            lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_PURGE, mode);
+        #endif
+
+        // Extrude filament to get into hotend
+        do_pause_e_move(purge_length, ADVANCED_PAUSE_EXTRUDE_FEEDRATE);
+      }
+
+      // Show "Purge More" / "Resume" menu and wait for reply
+      #if ENABLED(ULTIPANEL)
+        if (show_lcd) {
+          KEEPALIVE_STATE(PAUSED_FOR_USER);
+          wait_for_user = false;
+          lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_OPTION, mode);
+          while (advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_WAIT_FOR) idle(true);
+          KEEPALIVE_STATE(IN_HANDLER);
+        }
+      #endif
+
+      // Keep looping if "Purge More" was selected
+    } while (
+      #if ENABLED(ULTIPANEL)
+        show_lcd && advanced_pause_menu_response == ADVANCED_PAUSE_RESPONSE_EXTRUDE_MORE
+      #else
+        0
+      #endif
+    );
+
+  #endif      
 
   return true;
 }

Marlin/src/feature/pause.h

   ADVANCED_PAUSE_MESSAGE_INSERT,
   ADVANCED_PAUSE_MESSAGE_LOAD,
   ADVANCED_PAUSE_MESSAGE_PURGE,
+  #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
+    ADVANCED_PAUSE_MESSAGE_CONTINUOUS_PURGE,
+  #endif
   ADVANCED_PAUSE_MESSAGE_OPTION,
   ADVANCED_PAUSE_MESSAGE_RESUME,
   ADVANCED_PAUSE_MESSAGE_STATUS,

Marlin/src/lcd/ultralcd.cpp

     #else
       void lcd_temp_menu_e0_filament_change();
     #endif
-    void lcd_advanced_pause_option_menu();
-    void lcd_advanced_pause_init_message();
-    void lcd_advanced_pause_unload_message();
-    void lcd_advanced_pause_insert_message();
-    void lcd_advanced_pause_load_message();
-    void lcd_advanced_pause_heat_nozzle();
-    void lcd_advanced_pause_purge_message();
-    void lcd_advanced_pause_resume_message();
   #endif
 
   #if ENABLED(DAC_STEPPER_CURRENT)
       #if LCD_HEIGHT > _FC_LINES_G + 1
         STATIC_ITEM(" ");
       #endif
-      HOTEND_STATUS_ITEM();
+      HOTEND_STATUS_ITEM();                         
       END_SCREEN();
     }
 
+    #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
+      void lcd_advanced_pause_continuous_purge_menu() {
+        START_SCREEN();
+        STATIC_ITEM(MSG_FILAMENT_CHANGE_PURGE_1);
+        #ifdef MSG_FILAMENT_CHANGE_PURGE_2
+          STATIC_ITEM(MSG_FILAMENT_CHANGE_PURGE_2);
+          #define __FC_LINES_G 3
+        #else
+          #define __FC_LINES_G 2
+        #endif
+        #ifdef MSG_FILAMENT_CHANGE_PURGE_3
+          STATIC_ITEM(MSG_FILAMENT_CHANGE_PURGE_3);
+          #define _FC_LINES_G (__FC_LINES_G + 1)
+        #else
+          #define _FC_LINES_G __FC_LINES_G
+        #endif
+        #if LCD_HEIGHT > _FC_LINES_G + 1
+          STATIC_ITEM(" ");
+        #endif
+        HOTEND_STATUS_ITEM();
+        STATIC_ITEM(MSG_USERWAIT);
+        END_SCREEN();
+      }
+    #endif
+
     void lcd_advanced_pause_resume_message() {
       START_SCREEN();
       STATIC_ITEM_P(advanced_pause_header(), true, true);
         case ADVANCED_PAUSE_MESSAGE_WAIT_FOR_NOZZLES_TO_HEAT: return lcd_advanced_pause_wait_for_nozzles_to_heat;
         case ADVANCED_PAUSE_MESSAGE_OPTION: advanced_pause_menu_response = ADVANCED_PAUSE_RESPONSE_WAIT_FOR;
                                             return lcd_advanced_pause_option_menu;
+        #if ENABLED(ADVANCED_PAUSE_CONTINUOUS_PURGE)
+          case ADVANCED_PAUSE_MESSAGE_CONTINUOUS_PURGE: return lcd_advanced_pause_continuous_purge_menu;                                                                                              
+        #endif
         case ADVANCED_PAUSE_MESSAGE_STATUS:
         default: break;
       }