Move Delta settings lower in delta files

Marlin/example_configurations/delta/biv2.5/Configuration.h

 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
-
-//===========================================================================
-//============================== Delta Settings =============================
-//===========================================================================
-// Enable DELTA kinematics and most of the default configuration for Deltas
-#define DELTA
-
-// Make delta curves from many straight lines (linear interpolation).
-// This is a trade-off between visible corners (not enough segments)
-// and processor overload (too many expensive sqrt calls).
-#define DELTA_SEGMENTS_PER_SECOND 100
-
-// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
-
-// Center-to-center distance of the holes in the diagonal push rods.
-#define DELTA_DIAGONAL_ROD 440.0 // mm
-
-// Horizontal offset from middle of printer to smooth rod center.
-#define DELTA_SMOOTH_ROD_OFFSET 330.0 // mm
-
-// Horizontal offset of the universal joints on the end effector.
-#define DELTA_EFFECTOR_OFFSET 50.0 // mm
-
-// Horizontal offset of the universal joints on the carriages.
-#define DELTA_CARRIAGE_OFFSET 20.0 // mm
-
-// Horizontal distance bridged by diagonal push rods when effector is centered.
-#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
-
-// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-#define DELTA_PRINTABLE_RADIUS 160
-
 // @section temperature
 
 //===========================================================================
 // Uncomment this option to enable CoreXY kinematics
 // #define COREXY
 
+//===========================================================================
+//============================== Delta Settings =============================
+//===========================================================================
+// Enable DELTA kinematics and most of the default configuration for Deltas
+#define DELTA
+
+#ifdef DELTA
+
+// Make delta curves from many straight lines (linear interpolation).
+// This is a trade-off between visible corners (not enough segments)
+// and processor overload (too many expensive sqrt calls).
+#define DELTA_SEGMENTS_PER_SECOND 100
+
+// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+// Center-to-center distance of the holes in the diagonal push rods.
+#define DELTA_DIAGONAL_ROD 440.0 // mm
+
+// Horizontal offset from middle of printer to smooth rod center.
+#define DELTA_SMOOTH_ROD_OFFSET 330.0 // mm
+
+// Horizontal offset of the universal joints on the end effector.
+#define DELTA_EFFECTOR_OFFSET 50.0 // mm
+
+// Horizontal offset of the universal joints on the carriages.
+#define DELTA_CARRIAGE_OFFSET 20.0 // mm
+
+// Horizontal distance bridged by diagonal push rods when effector is centered.
+#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
+
+// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+#define DELTA_PRINTABLE_RADIUS 160
+
+#endif
+
 // Enable this option for Toshiba steppers
 // #define CONFIG_STEPPERS_TOSHIBA
 

Marlin/example_configurations/delta/generic/Configuration.h

 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
-
-//===========================================================================
-//============================== Delta Settings =============================
-//===========================================================================
-// Enable DELTA kinematics and most of the default configuration for Deltas
-#define DELTA
-
-// Make delta curves from many straight lines (linear interpolation).
-// This is a trade-off between visible corners (not enough segments)
-// and processor overload (too many expensive sqrt calls).
-#define DELTA_SEGMENTS_PER_SECOND 200
-
-// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
-
-// Center-to-center distance of the holes in the diagonal push rods.
-#define DELTA_DIAGONAL_ROD 250.0 // mm
-
-// Horizontal offset from middle of printer to smooth rod center.
-#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm
-
-// Horizontal offset of the universal joints on the end effector.
-#define DELTA_EFFECTOR_OFFSET 33.0 // mm
-
-// Horizontal offset of the universal joints on the carriages.
-#define DELTA_CARRIAGE_OFFSET 18.0 // mm
-
-// Horizontal distance bridged by diagonal push rods when effector is centered.
-#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
-
-// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-#define DELTA_PRINTABLE_RADIUS 140
-
 // @section temperature
 
 //===========================================================================
 // Uncomment this option to enable CoreXY kinematics
 // #define COREXY
 
+//===========================================================================
+//============================== Delta Settings =============================
+//===========================================================================
+// Enable DELTA kinematics and most of the default configuration for Deltas
+#define DELTA
+
+#ifdef DELTA
+
+// Make delta curves from many straight lines (linear interpolation).
+// This is a trade-off between visible corners (not enough segments)
+// and processor overload (too many expensive sqrt calls).
+#define DELTA_SEGMENTS_PER_SECOND 200
+
+// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+// Center-to-center distance of the holes in the diagonal push rods.
+#define DELTA_DIAGONAL_ROD 250.0 // mm
+
+// Horizontal offset from middle of printer to smooth rod center.
+#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm
+
+// Horizontal offset of the universal joints on the end effector.
+#define DELTA_EFFECTOR_OFFSET 33.0 // mm
+
+// Horizontal offset of the universal joints on the carriages.
+#define DELTA_CARRIAGE_OFFSET 18.0 // mm
+
+// Horizontal distance bridged by diagonal push rods when effector is centered.
+#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
+
+// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+#define DELTA_PRINTABLE_RADIUS 140
+
+#endif
+
 // Enable this option for Toshiba steppers
 // #define CONFIG_STEPPERS_TOSHIBA
 

Marlin/example_configurations/delta/kossel_mini/Configuration.h

 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
 // #define PS_DEFAULT_OFF
 
-
-//===========================================================================
-//============================== Delta Settings =============================
-//===========================================================================
-// Enable DELTA kinematics and most of the default configuration for Deltas
-#define DELTA
-
-// Make delta curves from many straight lines (linear interpolation).
-// This is a trade-off between visible corners (not enough segments)
-// and processor overload (too many expensive sqrt calls).
-#define DELTA_SEGMENTS_PER_SECOND 200
-
-// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
-
-// Center-to-center distance of the holes in the diagonal push rods.
-#define DELTA_DIAGONAL_ROD 215.0 // mm
-
-// Horizontal offset from middle of printer to smooth rod center.
-#define DELTA_SMOOTH_ROD_OFFSET 145.0 // mm
-
-// Horizontal offset of the universal joints on the end effector.
-#define DELTA_EFFECTOR_OFFSET 19.9 // mm
-
-// Horizontal offset of the universal joints on the carriages.
-#define DELTA_CARRIAGE_OFFSET 19.5 // mm
-
-// Horizontal distance bridged by diagonal push rods when effector is centered.
-#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
-
-// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-#define DELTA_PRINTABLE_RADIUS 90
-
 // @section temperature
 
 //===========================================================================
 // Uncomment this option to enable CoreXY kinematics
 // #define COREXY
 
+//===========================================================================
+//============================== Delta Settings =============================
+//===========================================================================
+// Enable DELTA kinematics and most of the default configuration for Deltas
+#define DELTA
+
+#ifdef DELTA
+
+// Make delta curves from many straight lines (linear interpolation).
+// This is a trade-off between visible corners (not enough segments)
+// and processor overload (too many expensive sqrt calls).
+#define DELTA_SEGMENTS_PER_SECOND 200
+
+// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+// Center-to-center distance of the holes in the diagonal push rods.
+#define DELTA_DIAGONAL_ROD 215.0 // mm
+
+// Horizontal offset from middle of printer to smooth rod center.
+#define DELTA_SMOOTH_ROD_OFFSET 145.0 // mm
+
+// Horizontal offset of the universal joints on the end effector.
+#define DELTA_EFFECTOR_OFFSET 19.9 // mm
+
+// Horizontal offset of the universal joints on the carriages.
+#define DELTA_CARRIAGE_OFFSET 19.5 // mm
+
+// Horizontal distance bridged by diagonal push rods when effector is centered.
+#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET)
+
+// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+#define DELTA_PRINTABLE_RADIUS 90
+
+#endif
+
 // Enable this option for Toshiba steppers
 // #define CONFIG_STEPPERS_TOSHIBA