EXTUI and UBL compilation fixes (#13420)

Marlin/src/feature/bedlevel/ubl/ubl.cpp

   #include "../../../module/motion.h"
   #include "../../bedlevel/bedlevel.h"
 
+  #if ENABLED(EXTENSIBLE_UI)
+    #include "../../../lcd/extensible_ui/ui_api.h"
+  #endif
+  
   #include "math.h"
 
   void unified_bed_leveling::echo_name() {

Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp

   #define DEBUG_OUT ENABLED(DEBUG_LEVELING_FEATURE)
   #include "../../../core/debug_out.h"
 
+  #if ENABLED(EXTENSIBLE_UI)
+    #include "../../../lcd/extensible_ui/ui_api.h"
+  #endif
+
   #include <math.h>
 
   #define UBL_G29_P31
 
         case 2:
           // Allow the user to specify the height because 10mm is a little extreme in some cases.
-          for (uint8_t x = (GRID_MAX_POINTS_X) / 3; x < 2 * (GRID_MAX_POINTS_X) / 3; x++)   // Create a rectangular raised area in
-            for (uint8_t y = (GRID_MAX_POINTS_Y) / 3; y < 2 * (GRID_MAX_POINTS_Y) / 3; y++) // the center of the bed
+          for (uint8_t x = (GRID_MAX_POINTS_X) / 3; x < 2 * (GRID_MAX_POINTS_X) / 3; x++)     // Create a rectangular raised area in
+            for (uint8_t y = (GRID_MAX_POINTS_Y) / 3; y < 2 * (GRID_MAX_POINTS_Y) / 3; y++) { // the center of the bed
               z_values[x][y] += parser.seen('C') ? g29_constant : 9.99f;
               #if ENABLED(EXTENSIBLE_UI)
                 ExtUI::onMeshUpdate(x, y, z_values[x][y]);
               #endif
+            }
           break;
       }
     }

Marlin/src/gcode/bedlevel/ubl/M421.cpp

 #include "../../gcode.h"
 #include "../../../feature/bedlevel/bedlevel.h"
 
+#if ENABLED(EXTENSIBLE_UI)
+  #include "../../../lcd/extensible_ui/ui_api.h"
+#endif
+
 /**
  * M421: Set a single Mesh Bed Leveling Z coordinate
  *

Marlin/src/lcd/extensible_ui/ui_api.cpp

   #endif
 #endif
 
+#if HAS_LEVELING
+  #include "../../feature/bedlevel.h"
+#endif
+
 #if HAS_FILAMENT_SENSOR
   #include "../../feature/runout.h"
 #endif
 
     void setJunctionDeviation_mm(const float value) {
       planner.junction_deviation_mm = clamp(value, 0.01, 0.3);
-      planner.recalculate_max_e_jerk();
+      #if ENABLED(LIN_ADVANCE)
+        planner.recalculate_max_e_jerk();
+      #endif
     }
 
   #else
 
   #if HAS_LEVELING
     bool getLevelingActive() { return planner.leveling_active; }
-    void setLevelingActive(const bool state) { set_bed_leveling_enabled(state) }
+    void setLevelingActive(const bool state) { set_bed_leveling_enabled(state); }
     #if HAS_MESH
       bool getMeshValid() { return leveling_is_valid(); }
       bed_mesh_t getMeshArray() { return Z_VALUES; }

config/default/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/AlephObjects/TAZ4/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/AliExpress/UM2pExt/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Anet/A2/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Anet/A2plus/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Anet/A6/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Anet/A8/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/AnyCubic/i3/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/ArmEd/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/BIBO/TouchX/default/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Cartesio/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Creality/CR-10/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Creality/CR-10S/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Creality/CR-10_5S/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Creality/CR-10mini/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Creality/CR-8/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Creality/Ender-4/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Einstart-S/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Felix/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/FolgerTech/i3-2020/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Formbot/Raptor/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Formbot/T_Rex_3/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Geeetech/A10M/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Geeetech/A20M/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Geeetech/MeCreator2/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Infitary/i3-M508/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/MakerParts/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Malyan/M150/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Malyan/M200/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Micromake/C1/enhanced/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Mks/Robin/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Mks/Sbase/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/RapideLite/RL200/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/RigidBot/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Sanguinololu/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/TheBorg/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/TinyBoy2/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Tronxy/X3A/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Tronxy/X5S-2E/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/UltiMachine/Archim1/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/UltiMachine/Archim2/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/VORONDesign/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Velleman/K8200/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/Velleman/K8400/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/WASP/PowerWASP/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/gCreate/gMax1.5+/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/makibox/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/tvrrug/Round2/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif

config/examples/wt150/Configuration_adv.h

 
 // @section lcd
 
-#if ENABLED(ULTIPANEL)
+#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+#endif
+
+#if ENABLED(ULTIPANEL)
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif