Support SWITCHING_NOZZLE with 2 servos (#13054)

Marlin/Configuration.h

   #endif
 #endif
 
-// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
+// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/Marlin.cpp

   #endif
 
   #if ENABLED(SWITCHING_NOZZLE)
-    move_nozzle_servo(0);     // Initialize nozzle servo
+    // Initialize nozzle servo(s)
+    #if SWITCHING_NOZZLE_TWO_SERVOS
+      lower_nozzle(0);
+      raise_nozzle(1);
+    #else
+      move_nozzle_servo(0);
+    #endif
   #endif
 
   #if ENABLED(PARKING_EXTRUDER)

Marlin/src/config/default/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/3DFabXYZ/Migbot/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Anet/A2/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Anet/A2plus/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Anet/A6/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Anet/A8/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/AnyCubic/i3/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/ArmEd/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Cartesio/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Creality/CR-10/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Creality/CR-8/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Creality/Ender-2/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Creality/Ender-3/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Creality/Ender-4/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Einstart-S/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Felix/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Felix/DUAL/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/FlashForge/CreatorPro/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Formbot/Raptor/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Geeetech/MeCreator2/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/JGAurora/A5/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/MakerParts/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Malyan/M150/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Malyan/M200/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Mks/Robin/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Mks/Sbase/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/RapideLite/RL200/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/RigidBot/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/SCARA/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/STM32F10/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/STM32F4/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Sanguinololu/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/TheBorg/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/TinyBoy2/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Tronxy/X1/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Tronxy/X3A/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Tronxy/X5S/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Tronxy/XY100/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/UltiMachine/Archim1/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/VORONDesign/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Velleman/K8200/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Velleman/K8400/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/WASP/PowerWASP/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/generic/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/makibox/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/stm32f103ret6/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/config/examples/wt150/Configuration.h

 //#define SWITCHING_NOZZLE
 #if ENABLED(SWITCHING_NOZZLE)
   #define SWITCHING_NOZZLE_SERVO_NR 0
-  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define SWITCHING_NOZZLE_E1_SERVO_NR 1          // If two servos are used, the index of the second
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
 #endif
 
 /**

Marlin/src/inc/Conditionals_LCD.h

 #define HOTEND_LOOP() for (int8_t e = 0; e < HOTENDS; e++)
 
 #define DO_SWITCH_EXTRUDER (ENABLED(SWITCHING_EXTRUDER) && (DISABLED(SWITCHING_NOZZLE) || SWITCHING_EXTRUDER_SERVO_NR != SWITCHING_NOZZLE_SERVO_NR))
+#define SWITCHING_NOZZLE_TWO_SERVOS defined(SWITCHING_NOZZLE_E1_SERVO_NR)
 
 #define HAS_HOTEND_OFFSET (HOTENDS > 1)
 

Marlin/src/inc/SanityCheck.h

     #error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS."
   #elif NUM_SERVOS < 1
     #error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1."
+  #endif
+
+  #ifndef SWITCHING_NOZZLE_SERVO_NR
+    #error "SWITCHING_NOZZLE requires SWITCHING_NOZZLE_SERVO_NR."
   #elif SWITCHING_NOZZLE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
     #error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE."
   #elif SWITCHING_NOZZLE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
   #elif SWITCHING_NOZZLE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
     #error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE."
   #endif
+
+  #ifdef SWITCHING_NOZZLE_E1_SERVO_NR
+    #if SWITCHING_NOZZLE_E1_SERVO_NR == SWITCHING_NOZZLE_SERVO_NR
+      #error "SWITCHING_NOZZLE_E1_SERVO_NR must be different from SWITCHING_NOZZLE_SERVO_NR."
+    #elif SWITCHING_NOZZLE_E1_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
+      #error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE."
+    #elif SWITCHING_NOZZLE_E1_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
+      #error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE."
+    #elif SWITCHING_NOZZLE_E1_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
+      #error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE."
+    #elif SWITCHING_NOZZLE_E1_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
+      #error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE."
+    #endif
+  #endif
 #endif
 
 /**

Marlin/src/module/tool_change.cpp

 #endif // DO_SWITCH_EXTRUDER
 
 #if ENABLED(SWITCHING_NOZZLE)
-  void move_nozzle_servo(const uint8_t e) {
-    planner.synchronize();
-    MOVE_SERVO(SWITCHING_NOZZLE_SERVO_NR, servo_angles[SWITCHING_NOZZLE_SERVO_NR][e]);
-    safe_delay(500);
-  }
+
+  #if SWITCHING_NOZZLE_TWO_SERVOS
+
+    inline void _move_nozzle_servo(const uint8_t e, const uint8_t angle_index) {
+      constexpr int8_t  sns_index[2] = { SWITCHING_NOZZLE_SERVO_NR, SWITCHING_NOZZLE_E1_SERVO_NR };
+      constexpr int16_t sns_angles[2] = SWITCHING_NOZZLE_SERVO_ANGLES;
+      planner.synchronize();
+      MOVE_SERVO(sns_index[e], sns_angles[angle_index]);
+      safe_delay(500);
+    }
+
+    void lower_nozzle(const uint8_t e) { _move_nozzle_servo(e, 0); }
+    void raise_nozzle(const uint8_t e) { _move_nozzle_servo(e, 1); }
+
+  #else
+
+    void move_nozzle_servo(const uint8_t angle_index) {
+      planner.synchronize();
+      MOVE_SERVO(SWITCHING_NOZZLE_SERVO_NR, servo_angles[SWITCHING_NOZZLE_SERVO_NR][e]);
+      safe_delay(500);
+    }
+
+  #endif
+
 #endif // SWITCHING_NOZZLE
 
 #if ENABLED(PARKING_EXTRUDER)
     #endif // TOOLCHANGE_FILAMENT_SWAP
 
     if (tmp_extruder != active_extruder) {
+
+      #if SWITCHING_NOZZLE_TWO_SERVOS
+        raise_nozzle(active_extruder);
+      #endif
+
       const float old_feedrate_mm_s = fr_mm_s > 0.0 ? fr_mm_s : feedrate_mm_s;
       feedrate_mm_s = fr_mm_s > 0.0 ? fr_mm_s : XY_PROBE_FEEDRATE_MM_S;
 
         parking_extruder_tool_change(tmp_extruder, no_move);
       #elif ENABLED(SWITCHING_TOOLHEAD) // Switching Toolhead
         switching_toolhead_tool_change(tmp_extruder, fr_mm_s, no_move);
-      #elif ENABLED(SWITCHING_NOZZLE)
-        // Always raise by a configured distance to avoid workpiece
+      #elif ENABLED(SWITCHING_NOZZLE) && !SWITCHING_NOZZLE_TWO_SERVOS
+        // Raise by a configured distance to avoid workpiece, except with
+        // SWITCHING_NOZZLE_TWO_SERVOS, as both nozzles will lift instead.
         current_position[Z_AXIS] += MAX(-zdiff, 0.0) + toolchange_settings.z_raise;
         #if HAS_SOFTWARE_ENDSTOPS
           NOMORE(current_position[Z_AXIS], soft_endstop_max[Z_AXIS]);
         mmu2.toolChange(tmp_extruder);
       #endif
 
+      #if SWITCHING_NOZZLE_TWO_SERVOS
+        lower_nozzle(active_extruder);
+      #endif
     } // (tmp_extruder != active_extruder)
 
     planner.synchronize();

Marlin/src/module/tool_change.h

 #endif
 
 #if ENABLED(SWITCHING_NOZZLE)
-  void move_nozzle_servo(const uint8_t e);
+  #if SWITCHING_NOZZLE_TWO_SERVOS
+    void lower_nozzle(const uint8_t e);
+    void raise_nozzle(const uint8_t e);
+  #else
+    void move_nozzle_servo(const uint8_t angle_index);
+  #endif
 #endif
 
 #if ENABLED(PARKING_EXTRUDER)

buildroot/share/tests/LPC1768_tests

 restore_configs
 opt_set MOTHERBOARD BOARD_MKS_SBASE
 opt_set EXTRUDERS 2
-opt_set NUM_SERVOS 1
-opt_enable SWITCHING_EXTRUDER ULTIMAKERCONTROLLER
-exec_test $1 $2 "MKS_SBASE SWITCHING_EXTRUDER"
+opt_set TEMP_SENSOR_1 1
+opt_set NUM_SERVOS 2
+opt_set SERVO_DELAY "{ 300, 300 }"
+opt_enable SWITCHING_NOZZLE SWITCHING_NOZZLE_E1_SERVO_NR ULTIMAKERCONTROLLER
+exec_test $1 $2 "MKS_SBASE SWITCHING_NOZZLE"
 
 restore_configs
 opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EEB
 opt_set EXTRUDERS 2
-opt_set TEMP_SENSOR_0 1
-opt_set TEMP_SENSOR_1 5
-opt_set TEMP_SENSOR_BED 1
+opt_set TEMP_SENSOR_1 -1
+opt_set TEMP_SENSOR_BED 5
 opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
            FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY \
            FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \