Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping

The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.

Marlin/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/default/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/default/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Anet/A6/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Anet/A8/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Cartesio/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Cartesio/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Creality/CR-10/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Creality/CR-8/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Creality/Ender-2/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Creality/Ender-3/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Creality/Ender-4/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Felix/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Felix/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Felix/DUAL/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/JGAurora/A5/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/MakerParts/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/MakerParts/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Malyan/M150/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Malyan/M200/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Mks/Sbase/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 4
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/RigidBot/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/RigidBot/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/SCARA/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/SCARA/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/STM32F10/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/STM32F4/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Sanguinololu/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/TheBorg/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/TheBorg/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/TinyBoy2/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba steppers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Tronxy/X1/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Tronxy/X5S/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Tronxy/XY100/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Velleman/K8200/Configuration.h

 #define INVERT_Y_DIR false // K8200: false
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Velleman/K8400/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h

 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h

 /**
  * Minimum stepper driver pulse width (in µs)
  *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
+ *   1 : Minimum for LV8729 stepper drivers
  *   2 : Minimum for DRV8825 stepper drivers
  *   3 : Minimum for TB6600 stepper drivers
  *  30 : Minimum for TB6560 stepper drivers
  */
 #define MINIMUM_STEPPER_PULSE 2
 
+/**
+ * Maximum stepping rate (in Hz) the stepper driver allows
+ *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
+ *  500000 : Maximum for A4988 stepper driver
+ *  400000 : Maximum for TMC2xxx stepper drivers
+ *  250000 : Maximum for DRV8825 stepper driver
+ *  150000 : Maximum for TB6600 stepper driver
+ *  130000 : Maximum for LV8729 stepper driver
+ *   15000 : Maximum for TB6560 stepper driver
+ */
+#define MAXIMUM_STEPPER_RATE 250000
+
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR true
 
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.