Merge pull request #1890 from thinkyhead/cold_extrude

Apply CUSTOM_MACHINE_NAME to configs

Marlin/Configuration.h

@@ -68,8 +68,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_RAMPS_13_EFB
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+// #define CUSTOM_MACHINE_NAME "This RepRap"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/Marlin_main.cpp

@@ -141,7 +141,7 @@
 // M150 - Set BlinkM Color Output R: Red<0-255> U(!): Green<0-255> B: Blue<0-255> over i2c, G for green does not work.
 // M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating
 //        Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling
-// M200 D<millimeters>- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).
+// M200 - set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).:D<millimeters>- 
 // M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
 // M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!!
 // M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
@@ -152,9 +152,9 @@
 // M208 - Set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec]
 // M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
 // M218 - Set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
-// M220 S<factor in percent>- set speed factor override percentage
-// M221 S<factor in percent>- set extrude factor override percentage
-// M226 P<pin number> S<pin state>- Wait until the specified pin reaches the state required
+// M220 - Set speed factor override percentage: S<factor in percent>
+// M221 - Set extrude factor override percentage: S<factor in percent>
+// M226 - Wait until the specified pin reaches the state required: P<pin number> S<pin state>
 // M240 - Trigger a camera to take a photograph
 // M250 - Set LCD contrast C<contrast value> (value 0..63)
 // M280 - Set servo position absolute. P: servo index, S: angle or microseconds
@@ -178,7 +178,7 @@
 // M503 - Print the current settings (from memory not from EEPROM). Use S0 to leave off headings.
 // M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
 // M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
-// M665 - Set delta configurations
+// M665 - Set delta configurations: L<diagonal rod> R<delta radius> S<segments/s>
 // M666 - Set delta endstop adjustment
 // M605 - Set dual x-carriage movement mode: S<mode> [ X<duplication x-offset> R<duplication temp offset> ]
 // M907 - Set digital trimpot motor current using axis codes.

Marlin/configurator/config/Configuration.h

@@ -68,8 +68,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_RAMPS_13_EFB
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+// #define CUSTOM_MACHINE_NAME "This RepRap"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/configurator/config/language.h

@@ -75,7 +75,7 @@
 #endif
 
 #ifdef CUSTOM_MENDEL_NAME
-  #warning CUSTOM_MENDEL_NAME deprecated - use CUSTOM_MACHINE_NAME
+  #error CUSTOM_MENDEL_NAME deprecated - use CUSTOM_MACHINE_NAME
   #define CUSTOM_MACHINE_NAME CUSTOM_MENDEL_NAME
 #endif
 

Marlin/configurator/index.html

@@ -46,7 +46,7 @@
 
           <label class="newline">Motherboard:</label><select name="MOTHERBOARD"></select>
 
-          <label class="newline">Custom Name:</label><input name="CUSTOM_MENDEL_NAME" type="text" size="14" maxlength="12" value="" />
+          <label class="newline">Custom Name:</label><input name="CUSTOM_MACHINE_NAME" type="text" size="14" maxlength="12" value="" />
 
           <label class="newline">Machine UUID:</label><input name="MACHINE_UUID" type="text" size="38" maxlength="36" value="" />
 

Marlin/example_configurations/Felix/Configuration.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_FELIX2
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+#define CUSTOM_MACHINE_NAME "Felix"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_FELIX2
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+#define CUSTOM_MACHINE_NAME "Felix Dual"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/Hephestos/Configuration.h

@@ -62,8 +62,8 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_HEPHESTOS
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/K8200/Configuration.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_K8200
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+// #define CUSTOM_MACHINE_NAME "This RepRap"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/SCARA/Configuration.h

@@ -80,8 +80,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_RAMPS_13_EFB
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+// #define CUSTOM_MACHINE_NAME "This RepRap"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/WITBOX/Configuration.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_WITBOX
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+// #define CUSTOM_MACHINE_NAME "This RepRap"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/delta/generic/Configuration.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_RAMPS_13_EFB
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+#define CUSTOM_MACHINE_NAME "Deltabot"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_RAMPS_13_EFB
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-#define CUSTOM_MENDEL_NAME "Mini Kossel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+#define CUSTOM_MACHINE_NAME "Mini Kossel"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/makibox/Configuration.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_5DPRINT
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+// #define CUSTOM_MACHINE_NAME "This RepRap"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -62,8 +62,9 @@ Here are some standard links for getting your machine calibrated:
   #define MOTHERBOARD BOARD_OMCA
 #endif
 
-// Define this to set a custom name for your generic Mendel,
-// #define CUSTOM_MENDEL_NAME "This Mendel"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+// #define CUSTOM_MACHINE_NAME "This RepRap"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)

Marlin/language.h

@@ -75,7 +75,7 @@
 #endif
 
 #ifdef CUSTOM_MENDEL_NAME
-  #warning CUSTOM_MENDEL_NAME deprecated - use CUSTOM_MACHINE_NAME
+  #error CUSTOM_MENDEL_NAME deprecated - use CUSTOM_MACHINE_NAME
   #define CUSTOM_MACHINE_NAME CUSTOM_MENDEL_NAME
 #endif