Move probe extras below probe types

Marlin/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/default/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -791,20 +791,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -884,6 +870,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Anet/A2/Configuration.h

@@ -754,20 +754,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -847,6 +833,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Anet/A2plus/Configuration.h

@@ -754,20 +754,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -847,6 +833,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -819,20 +819,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -941,6 +927,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -778,20 +778,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -871,6 +857,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -743,20 +743,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -836,6 +822,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

@@ -743,20 +743,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -836,6 +822,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -759,20 +759,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -852,6 +838,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -772,20 +772,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -865,6 +851,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -759,20 +759,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -852,6 +838,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -770,20 +770,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -863,6 +849,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 1

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -781,20 +781,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,6 +860,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

@@ -775,20 +775,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -868,6 +854,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

@@ -790,20 +790,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -883,6 +869,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Creality/CR-8/Configuration.h

@@ -781,20 +781,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,6 +860,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Creality/Ender-2/Configuration.h

@@ -775,20 +775,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -868,6 +854,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Creality/Ender-3/Configuration.h

@@ -775,20 +775,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -868,6 +854,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Creality/Ender-4/Configuration.h

@@ -781,20 +781,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,6 +860,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Einstart-S/Configuration.h

@@ -782,20 +782,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,6 +860,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 1

Marlin/src/config/examples/Felix/Configuration.h

@@ -753,20 +753,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -846,6 +832,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -753,20 +753,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -846,6 +832,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -777,20 +777,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -870,6 +856,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 #define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h

@@ -795,20 +795,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -888,6 +874,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 #define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h

@@ -806,20 +806,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -899,6 +885,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 #define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -786,20 +786,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -879,6 +865,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -771,20 +771,6 @@
   #define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -787,20 +787,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
-#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -880,6 +866,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 #define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+#define PROBING_FANS_OFF          // Turn fans off when probing
+#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -786,20 +786,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -879,6 +865,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -775,20 +775,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -868,6 +854,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/JGAurora/A5/Configuration.h

@@ -783,20 +783,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -876,6 +862,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/MakerParts/Configuration.h

@@ -791,20 +791,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -884,6 +870,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -763,20 +763,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -860,6 +846,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Malyan/M200/Configuration.h

@@ -770,20 +770,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -863,6 +849,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -775,20 +775,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -868,6 +854,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -775,20 +775,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -868,6 +854,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h

@@ -811,20 +811,6 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -904,6 +890,20 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -769,20 +769,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -862,6 +848,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/SCARA/Configuration.h

@@ -784,20 +784,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -877,6 +863,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -773,20 +773,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -866,6 +852,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/STM32F4/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -802,20 +802,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -895,6 +881,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/TheBorg/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 1

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -822,20 +822,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -915,6 +901,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Tronxy/X1/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Tronxy/X3A/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Tronxy/X5S/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Tronxy/XY100/Configuration.h

@@ -782,20 +782,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -875,6 +861,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -800,20 +800,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -893,6 +879,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -781,20 +781,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,6 +860,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -771,20 +771,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,6 +850,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -894,20 +894,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -915,9 +901,52 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
+ */
+//#define Z_PROBE_ALLEN_KEY
+
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0
+  #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0
+  #define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0
+  #define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_SPEED
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4_X 0.0
+  #define Z_PROBE_ALLEN_KEY_STOW_4_Y 0.0
+  #define Z_PROBE_ALLEN_KEY_STOW_4_Z Z_PROBE_ALLEN_KEY_STOW_3_Z
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
@@ -967,53 +996,6 @@
 #define MULTIPLE_PROBING 3
 
 /**
- * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
- * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
- */
-//#define Z_PROBE_ALLEN_KEY
-
-#if ENABLED(Z_PROBE_ALLEN_KEY)
-  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
-  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
-
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED
-
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10
-
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z
-  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED
-
-  #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position
-  #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0
-  #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0
-  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED
-
-  #define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down
-  #define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0
-  #define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0
-  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED)/10
-
-  #define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear
-  #define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0
-  #define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0
-  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_SPEED
-
-  #define Z_PROBE_ALLEN_KEY_STOW_4_X 0.0
-  #define Z_PROBE_ALLEN_KEY_STOW_4_Y 0.0
-  #define Z_PROBE_ALLEN_KEY_STOW_4_Z Z_PROBE_ALLEN_KEY_STOW_3_Z
-  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED
-
-#endif // Z_PROBE_ALLEN_KEY
-
-/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -1043,6 +1025,20 @@
   #define Z_MIN_PROBE_REPEATABILITY_TEST
 #endif
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -853,20 +853,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,50 +860,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 0     // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10  // Z offset: -below +above  [the nozzle]
-
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 20
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 5000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-//#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -969,6 +911,46 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 0     // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10  // Z offset: -below +above  [the nozzle]
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 20
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 5000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -996,6 +978,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h

@@ -853,20 +853,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,50 +860,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 0     // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10  // Z offset: -below +above  [the nozzle]
-
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 20
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 5000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-//#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -968,6 +910,46 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 0     // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.10  // Z offset: -below +above  [the nozzle]
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 20
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 5000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -995,6 +977,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -853,20 +853,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -874,50 +860,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25  // Z offset: -below +above  [the nozzle]
-
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 10
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 2000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -968,6 +910,46 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25  // Z offset: -below +above  [the nozzle]
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 10
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 2000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -995,6 +977,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 #define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h

@@ -858,20 +858,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -879,50 +865,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER 0  // Z offset: -below +above  [the nozzle]
-
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 10
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 4000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST (HOMING_FEEDRATE_Z / 4)
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 4)
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -971,6 +913,46 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 0   // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0  // Z offset: -below +above  [the nozzle]
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 10
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 4000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST (HOMING_FEEDRATE_Z / 4)
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 4)
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -998,6 +980,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -843,20 +843,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,50 +850,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // Z offset: -below +above  [the nozzle]
-
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 10
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 4000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-//#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -956,6 +898,46 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // Z offset: -below +above  [the nozzle]
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 10
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 4000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -983,6 +965,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -843,20 +843,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -864,50 +850,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // Z offset: -below +above  [the nozzle]
-
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 10
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 4000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-//#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -958,6 +900,46 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0     // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // Z offset: -below +above  [the nozzle]
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 10
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 4000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -985,6 +967,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -836,20 +836,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -857,53 +843,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER -23 // KosselPro actual: -22.919
-#define Y_PROBE_OFFSET_FROM_EXTRUDER -6  // KosselPro actual: -6.304
-/**
- * Kossel Pro note: The correct value is likely -17.45 but I'd rather err on the side of
- * not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed.
- */
-#define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25  // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero).
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 10
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 8000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-//#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -958,6 +897,49 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER -23 // KosselPro actual: -22.919
+#define Y_PROBE_OFFSET_FROM_EXTRUDER -6  // KosselPro actual: -6.304
+/**
+ * Kossel Pro note: The correct value is likely -17.45 but I'd rather err on the side of
+ * not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed.
+ */
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25  // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero).
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 10
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 8000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -986,6 +968,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -846,20 +846,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -867,50 +853,6 @@
 //#define Z_PROBE_SLED
 //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- *   X and Y offsets must be integers.
- *
- *   In the following example the X and Y offsets are both positive:
- *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- *      +-- BACK ---+
- *      |           |
- *    L |    (+) P  | R <-- probe (20,20)
- *    E |           | I
- *    F | (-) N (+) | G <-- nozzle (10,10)
- *    T |           | H
- *      |    (-)    | T
- *      |           |
- *      O-- FRONT --+
- *    (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 0.0     // Z probe to nozzle X offset: -left  +right
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0     // Z probe to nozzle Y offset: -front +behind
-#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3     // Z probe to nozzle Z offset: -below (always!)
-
-// Certain types of probes need to stay away from edges
-#define MIN_PROBE_EDGE 10
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 8000
-
-// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Feedrate (mm/m) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
-
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
-//#define MULTIPLE_PROBING 2
-
 /**
  * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
  * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
@@ -959,6 +901,46 @@
 #endif // Z_PROBE_ALLEN_KEY
 
 /**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0.0     // Z probe to nozzle X offset: -left  +right
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0     // Z probe to nozzle Y offset: -front +behind
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3     // Z probe to nozzle Z offset: -below (always!)
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 10
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 8000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
+
+/**
  * Z probes require clearance when deploying, stowing, and moving between
  * probe points to avoid hitting the bed and other hardware.
  * Servo-mounted probes require extra space for the arm to rotate.
@@ -986,6 +968,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -784,20 +784,6 @@
   #define BLTOUCH_DELAY 500   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -877,6 +863,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 #define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/makibox/Configuration.h

@@ -774,20 +774,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -867,6 +853,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/stm32f103ret6/Configuration.h

@@ -773,20 +773,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -866,6 +852,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -766,20 +766,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -859,6 +845,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 1

Marlin/src/config/examples/wt150/Configuration.h

@@ -776,20 +776,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -869,6 +855,20 @@
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
 
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
 #define X_ENABLE_ON 0