RETRACT_ZLIFT => RETRACT_ZRAISE

Marlin/Configuration_adv.h

@@ -1046,7 +1046,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/default/Configuration_adv.h

@@ -1046,7 +1046,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Anet/A2/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -1053,7 +1053,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Cartesio/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Einstart-S/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Felix/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Formbot/Raptor/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -1049,7 +1049,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -1050,7 +1050,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -1046,7 +1046,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/MakerParts/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@@ -1053,7 +1053,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/RigidBot/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/SCARA/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 35             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/TheBorg/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

@@ -1058,7 +1058,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/delta/generic/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

@@ -1047,7 +1047,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/makibox/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

@@ -1045,7 +1045,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -1046,7 +1046,7 @@
   #define RETRACT_LENGTH 3                // Default retract length (positive mm)
   #define RETRACT_LENGTH_SWAP 13          // Default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45             // Default feedrate for retracting (mm/s)
-  #define RETRACT_ZLIFT 0                 // Default retract Z-lift
+  #define RETRACT_ZRAISE 0                // Default retract Z-raise (mm)
   #define RETRACT_RECOVER_LENGTH 0        // Default additional recover length (mm, added to retract length when recovering)
   #define RETRACT_RECOVER_LENGTH_SWAP 0   // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8      // Default feedrate for recovering from retraction (mm/s)

Marlin/src/core/types.h

@@ -35,7 +35,7 @@ typedef struct {
 typedef struct {
   float retract_length,                     // M207 S - G10 Retract length
         retract_feedrate_mm_s,              // M207 F - G10 Retract feedrate
-        retract_zlift,                      // M207 Z - G10 Retract hop size
+        retract_zraise,                      // M207 Z - G10 Retract hop size
         retract_recover_length,             // M208 S - G11 Recover length
         retract_recover_feedrate_mm_s,      // M208 F - G11 Recover feedrate
         swap_retract_length,                // M207 W - G10 Swap Retract length

Marlin/src/feature/fwretract.cpp

@@ -65,7 +65,7 @@ void FWRetract::reset() {
   #endif
   settings.retract_length = RETRACT_LENGTH;
   settings.retract_feedrate_mm_s = RETRACT_FEEDRATE;
-  settings.retract_zlift = RETRACT_ZLIFT;
+  settings.retract_zraise = RETRACT_ZRAISE;
   settings.retract_recover_length = RETRACT_RECOVER_LENGTH;
   settings.retract_recover_feedrate_mm_s = RETRACT_RECOVER_FEEDRATE;
   settings.swap_retract_length = RETRACT_LENGTH_SWAP;
@@ -159,8 +159,8 @@ void FWRetract::retract(const bool retracting
     planner.synchronize();                                // Wait for move to complete
 
     // Is a Z hop set, and has the hop not yet been done?
-    if (settings.retract_zlift > 0.01 && !current_hop) {           // Apply hop only once
-      current_hop += settings.retract_zlift;                       // Add to the hop total (again, only once)
+    if (settings.retract_zraise > 0.01 && !current_hop) {           // Apply hop only once
+      current_hop += settings.retract_zraise;                       // Add to the hop total (again, only once)
       feedrate_mm_s = planner.settings.max_feedrate_mm_s[Z_AXIS] * unscale_fr;  // Maximum Z feedrate
       prepare_move_to_destination();                      // Raise up, set_current_to_destination
       planner.synchronize();                              // Wait for move to complete

Marlin/src/gcode/feature/fwretract/M207-M209.cpp

@@ -33,12 +33,12 @@
  *   S[+units]    retract_length
  *   W[+units]    swap_retract_length (multi-extruder)
  *   F[units/min] retract_feedrate_mm_s
- *   Z[units]     retract_zlift
+ *   Z[units]     retract_zraise
  */
 void GcodeSuite::M207() {
   if (parser.seen('S')) fwretract.settings.retract_length = parser.value_axis_units(E_AXIS);
   if (parser.seen('F')) fwretract.settings.retract_feedrate_mm_s = MMM_TO_MMS(parser.value_axis_units(E_AXIS));
-  if (parser.seen('Z')) fwretract.settings.retract_zlift = parser.value_linear_units();
+  if (parser.seen('Z')) fwretract.settings.retract_zraise = parser.value_linear_units();
   if (parser.seen('W')) fwretract.settings.swap_retract_length = parser.value_axis_units(E_AXIS);
 }
 

Marlin/src/inc/SanityCheck.h

@@ -309,6 +309,8 @@
   #error "MAX7219_DEBUG_STEPPER_QUEUE is now MAX7219_DEBUG_PLANNER_QUEUE. Please update your configuration."
 #elif defined(ENDSTOP_NOISE_FILTER)
   #error "ENDSTOP_NOISE_FILTER is now ENDSTOP_NOISE_THRESHOLD [2-7]. Please update your configuration."
+#elif defined(RETRACT_ZLIFT)
+  #error "RETRACT_ZLIFT is now RETRACT_ZRAISE. Please update your Configuration_adv.h."
 #endif
 
 #define BOARD_MKS_13     -47

Marlin/src/lcd/language/language_an.h

@@ -158,7 +158,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retraer mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Swap Retraer mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retraer  F")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Devantar mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Devantar mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("DesRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Swap DesRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("DesRet F")

Marlin/src/lcd/language/language_bg.h

@@ -127,7 +127,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Откат mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Смяна Откат mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Откат  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Скок mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Скок mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("Възврат mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Смяна Възврат mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("Възврат  V")

Marlin/src/lcd/language/language_ca.h

@@ -161,7 +161,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retreu mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Swap Retreure mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retreu V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Aixeca mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Aixeca mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("DesRet +mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Swap DesRet +mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("DesRet V")

Marlin/src/lcd/language/language_cz.h

@@ -268,7 +268,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retrakt mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Výměna Re.mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retraktovat  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Zvednuti Z mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Zvednuti Z mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("S UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_da.h

@@ -158,7 +158,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Tilbagetræk mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Skift Re.mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Tilbagetræk V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Skift UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_de.h

@@ -277,7 +277,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Rückzug mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Wechs. Rückzug mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Rückzug  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Z-Sprung mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Z-Sprung mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Wechs. UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_el-gr.h

@@ -156,7 +156,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Ανάσυρση μμ")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Εναλλαγή ανάσυρσης μμ")
 #define MSG_CONTROL_RETRACTF                _UxGT("Ανάσυρση V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Μεταπήδηση μμ")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Μεταπήδηση μμ")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("S UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_el.h

@@ -156,7 +156,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Ανάσυρση μμ")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Εναλλαγή ανάσυρσης μμ")  //SHORTEN
 #define MSG_CONTROL_RETRACTF                _UxGT("Ανάσυρση V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Μεταπήδηση μμ")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Μεταπήδηση μμ")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("S UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_en.h

@@ -756,8 +756,8 @@
 #ifndef MSG_CONTROL_RETRACTF
   #define MSG_CONTROL_RETRACTF                _UxGT("Retract  V")
 #endif
-#ifndef MSG_CONTROL_RETRACT_ZLIFT
-  #define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")
+#ifndef MSG_CONTROL_RETRACT_ZHOP
+  #define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")
 #endif
 #ifndef MSG_CONTROL_RETRACT_RECOVER
   #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")

Marlin/src/lcd/language/language_es.h

@@ -155,7 +155,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retraer mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Interc. Retraer mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retraer  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Levantar mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Levantar mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("DesRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Interc. DesRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("DesRet V")

Marlin/src/lcd/language/language_eu.h

@@ -259,7 +259,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Atzera egin mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Swap Atzera mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Atzera egin V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Igo mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Igo mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("Atzera egin mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Swap Atzera mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("Atzera egin V")

Marlin/src/lcd/language/language_fi.h

@@ -148,7 +148,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Vedä mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Va. Vedä mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Vedä V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Z mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Z mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Va. UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_fr.h

@@ -261,7 +261,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retrait mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Ech. Retr. mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retrait V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Saut Z mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Saut Z mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("Rappel mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Ech. Rappel mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("Rappel V")

Marlin/src/lcd/language/language_gl.h

@@ -157,7 +157,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retraccion mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Cambio retra. mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retraccion V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Alzar Z mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Alzar Z mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("Recup. retra. mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Cambio recup. mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("Recuperacion V")

Marlin/src/lcd/language/language_hr.h

@@ -157,7 +157,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retract mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Swap Re.mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retract  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("S UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_it.h

@@ -274,7 +274,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Ritrai mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Scamb. Ritrai mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Ritrai  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Salta mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Salta mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Scamb. UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet V")

Marlin/src/lcd/language/language_jp-kana.h

@@ -152,7 +152,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("ヒキコミリョウ mm")                // "Retract mm"
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("ヒキコミリョウS mm")               // "Swap Re.mm"
 #define MSG_CONTROL_RETRACTF                _UxGT("ヒキコミソクド mm/s")             // "Retract  V"
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("ノズルタイヒ mm")                // "Hop mm"
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("ノズルタイヒ mm")                // "Hop mm"
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("ホショウリョウ mm")               // "UnRet mm"
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("ホショウリョウS mm")              // "S UnRet mm"
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("ホショウソクド mm/s")            // "UnRet  V"

Marlin/src/lcd/language/language_ko_KR.h

@@ -274,7 +274,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retract mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Swap Re.mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retract  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("S UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet V")

Marlin/src/lcd/language/language_nl.h

@@ -166,7 +166,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retract mm")  //accepted English term in Dutch
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Ruil Retract mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retract  F")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Ruil UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  F")

Marlin/src/lcd/language/language_pl.h

@@ -157,7 +157,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Wycofaj mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Z Wycof. mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Wycofaj  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Skok Z mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Skok Z mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("Cof. wycof. mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Z Cof. wyc. mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("Cof. wycof.  V")

Marlin/src/lcd/language/language_pt-br.h

@@ -267,7 +267,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retrair mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Retrair Troca mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retrair V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Saltar mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Saltar mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("Des-Retrair mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Des-RetTroca mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("Des-Retrair  V")

Marlin/src/lcd/language/language_pt.h

@@ -154,7 +154,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT(" Retrair mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Troca Retrair mm")
 #define MSG_CONTROL_RETRACTF                _UxGT(" Retrair  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT(" Levantar mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT(" Levantar mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT(" DesRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Troca DesRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT(" DesRet  V")

Marlin/src/lcd/language/language_ru.h

@@ -261,7 +261,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Втягивание мм")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Втягивание смены мм")
 #define MSG_CONTROL_RETRACTF                _UxGT("Втягивание V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Втяг. прыжка мм")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Втяг. прыжка мм")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("Возврат мм")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("Возврат смены мм")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("Возврат V")

Marlin/src/lcd/language/language_sk.h

@@ -288,7 +288,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Retrakt mm")
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Výmena Re.mm")
 #define MSG_CONTROL_RETRACTF                _UxGT("Retraktovať  V")
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Zdvih Z mm")
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Zdvih Z mm")
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("S UnRet mm")
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")

Marlin/src/lcd/language/language_tr.h

@@ -166,7 +166,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("Geri Çek mm")                                        // Geri Çek mm
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("Swap Re.mm")                                         // Swap Re.mm
 #define MSG_CONTROL_RETRACTF                _UxGT("Geri Çekme  V")                                      // Geri Çekme V
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")                                             // Hop mm
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")                                             // Hop mm
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("UnRet mm")                                           // UnRet mm
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("S UnRet mm")                                         // S UnRetmm
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("UnRet  V")                                           // UnRet V

Marlin/src/lcd/language/language_zh_CN.h

@@ -259,7 +259,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("回抽长度mm")  //"Retract mm" retract_length, retract length (positive mm)
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("换手回抽长度mm")  //"Swap Re.mm" swap_retract_length, swap retract length (positive mm), for extruder change
 #define MSG_CONTROL_RETRACTF                _UxGT("回抽速率mm/s")  //"Retract  V" retract_feedrate_mm_s, feedrate for retracting (mm/s)
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")  //"Hop mm" retract_zlift, retract Z-lift
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")  //"Hop mm" retract_zraise, retract Z-lift
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("回抽恢复长度mm")  //"UnRet +mm" retract_recover_length, additional recover length (mm, added to retract length when recovering)
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("换手回抽恢复长度mm")  //"S UnRet+mm" swap_retract_recover_length, additional swap recover length (mm, added to retract length when recovering from extruder change)
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("回抽恢复后进料速率mm/s")  //"UnRet  V" retract_recover_feedrate_mm_s, feedrate for recovering from retraction (mm/s)

Marlin/src/lcd/language/language_zh_TW.h

@@ -259,7 +259,7 @@
 #define MSG_CONTROL_RETRACT                 _UxGT("回縮長度mm")  //"Retract mm" retract_length, retract length (positive mm)
 #define MSG_CONTROL_RETRACT_SWAP            _UxGT("換手回抽長度mm")  //"Swap Re.mm" swap_retract_length, swap retract length (positive mm), for extruder change
 #define MSG_CONTROL_RETRACTF                _UxGT("回縮速率mm/s")  //"Retract  V" retract_feedrate_mm_s, feedrate for retracting (mm/s)
-#define MSG_CONTROL_RETRACT_ZLIFT           _UxGT("Hop mm")  //"Hop mm" retract_zlift, retract Z-lift
+#define MSG_CONTROL_RETRACT_ZHOP            _UxGT("Hop mm")  //"Hop mm" retract_zraise, retract Z-lift
 #define MSG_CONTROL_RETRACT_RECOVER         _UxGT("回縮恢復長度mm")  //"UnRet +mm" retract_recover_length, additional recover length (mm, added to retract length when recovering)
 #define MSG_CONTROL_RETRACT_RECOVER_SWAP    _UxGT("換手回縮恢復長度mm")  //"S UnRet+mm" swap_retract_recover_length, additional swap recover length (mm, added to retract length when recovering from extruder change)
 #define MSG_CONTROL_RETRACT_RECOVERF        _UxGT("回縮恢復後進料速率mm/s")  //"UnRet V" retract_recover_feedrate_mm_s, feedrate for recovering from retraction (mm/s)

Marlin/src/lcd/ultralcd.cpp

@@ -4216,7 +4216,7 @@ void lcd_quick_feedback(const bool clear_buttons) {
         MENU_ITEM_EDIT(float52sign, MSG_CONTROL_RETRACT_SWAP, &fwretract.settings.swap_retract_length, 0, 100);
       #endif
       MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACTF, &fwretract.settings.retract_feedrate_mm_s, 1, 999);
-      MENU_ITEM_EDIT(float52sign, MSG_CONTROL_RETRACT_ZLIFT, &fwretract.settings.retract_zlift, 0, 999);
+      MENU_ITEM_EDIT(float52sign, MSG_CONTROL_RETRACT_ZHOP, &fwretract.settings.retract_zraise, 0, 999);
       MENU_ITEM_EDIT(float52sign, MSG_CONTROL_RETRACT_RECOVER, &fwretract.settings.retract_recover_length, -100, 100);
       #if EXTRUDERS > 1
         MENU_ITEM_EDIT(float52sign, MSG_CONTROL_RETRACT_RECOVER_SWAP, &fwretract.settings.swap_retract_recover_length, -100, 100);

Marlin/src/module/configuration_store.cpp

@@ -2552,7 +2552,7 @@ void MarlinSettings::reset(PORTARG_SOLO) {
       SERIAL_ECHOPAIR_P(port, "  M207 S", LINEAR_UNIT(fwretract.settings.retract_length));
       SERIAL_ECHOPAIR_P(port, " W", LINEAR_UNIT(fwretract.settings.swap_retract_length));
       SERIAL_ECHOPAIR_P(port, " F", MMS_TO_MMM(LINEAR_UNIT(fwretract.settings.retract_feedrate_mm_s)));
-      SERIAL_ECHOLNPAIR_P(port, " Z", LINEAR_UNIT(fwretract.settings.retract_zlift));
+      SERIAL_ECHOLNPAIR_P(port, " Z", LINEAR_UNIT(fwretract.settings.retract_zraise));
 
       if (!forReplay) {
         CONFIG_ECHO_START;