Update Watchdog description

Marlin/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

Marlin/src/HAL/HAL_AVR/watchdog_AVR.cpp

     #define WDTO_NS WDTO_4S
   #endif
   #if ENABLED(WATCHDOG_RESET_MANUAL)
-    // We enable the watchdog timer, but only for the interrupt.
+    // Enable the watchdog timer, but only for the interrupt.
     // Take care, as this requires the correct order of operation, with interrupts disabled.
     // See the datasheet of any AVR chip for details.
     wdt_reset();
     SERIAL_ERROR_MSG(MSG_WATCHDOG_FIRED);
     minkill();  // interrupt-safe final kill and infinite loop
   }
-#endif // WATCHDOG_RESET_MANUAL
+#endif
 
 #endif // USE_WATCHDOG
 #endif // __AVR__

config/default/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/AlephObjects/TAZ4/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/AliExpress/UM2pExt/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Anet/A2/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Anet/A2plus/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Anet/A6/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Anet/A8/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/AnyCubic/i3/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/ArmEd/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/BIBO/TouchX/default/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/BQ/Hephestos/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/BQ/Hephestos_2/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/BQ/WITBOX/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Cartesio/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/CR-10/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/CR-10S/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/CR-10_5S/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/CR-10mini/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/CR-8/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/Ender-2/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/Ender-3/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Creality/Ender-4/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Einstart-S/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Felix/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/FlashForge/CreatorPro/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/FolgerTech/i3-2020/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Formbot/Raptor/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Formbot/T_Rex_3/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Geeetech/A10M/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Geeetech/A20M/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Geeetech/MeCreator2/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Infitary/i3-M508/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/JGAurora/A5/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/MakerParts/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Malyan/M150/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Malyan/M200/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Micromake/C1/enhanced/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Mks/Robin/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Mks/Sbase/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/RapideLite/RL200/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/RigidBot/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/SCARA/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Sanguinololu/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/TheBorg/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 //#define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/TinyBoy2/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Tronxy/X3A/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Tronxy/X5S-2E/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/UltiMachine/Archim1/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/UltiMachine/Archim2/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 //#define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/VORONDesign/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Velleman/K8200/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Velleman/K8400/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/WASP/PowerWASP/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/FLSUN/kossel/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/MKS/SBASE/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/Tevo Little Monster/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/generic/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/kossel_mini/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/delta/kossel_xl/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/gCreate/gMax1.5+/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/makibox/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/tvrrug/Round2/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif
 

config/examples/wt150/Configuration_adv.h

 
 // @section safety
 
-// The hardware watchdog should reset the microcontroller disabling all outputs,
-// in case the firmware gets stuck and doesn't do temperature regulation.
+/**
+ * The watchdog hardware timer will do a reset and disable all outputs
+ * if the firmware gets too overloaded to read the temperature sensors.
+ *
+ * If you find that watchdog reboot causes your AVR board to hang forever,
+ * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
+ * NOTE: This method is less reliable as it can only catch hangups while
+ * interrupts are enabled.
+ */
 #define USE_WATCHDOG
-
 #if ENABLED(USE_WATCHDOG)
-  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
-  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
-  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
   //#define WATCHDOG_RESET_MANUAL
 #endif