Reformat pins files

Marlin/src/pins/linux/pins_RAMPS_LINUX.h

 #endif
 
 #ifndef MARLIN_EEPROM_SIZE
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 #define IS_RAMPS_EFB

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h

   #define E1_SERIAL_RX_PIN                 P1_01
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 /**

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h

   #define Z2_SERIAL_RX_PIN                 P1_01
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //

Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h

 #endif
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Steppers

Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h

 #define BOARD_INFO_NAME "GMARSH X6 REV1"
 
 // Ignore temp readings during develpment.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Enable 12MHz clock output on P1.27 pin to sync TMC2208 chip clocks
   #define E2_SERIAL_RX_PIN                 P2_06
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #else
   #error "TMC2208 UART configuration is required for GMarsh X6."
 #endif

Marlin/src/pins/lpc1768/pins_MKS_SBASE.h

   #define E0_SERIAL_RX_PIN                 P0_26  // TH4
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 // UNUSED

Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h

   #define Z2_SERIAL_RX_PIN                 P1_17
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif // TMC2208 || TMC2209
 
 //

Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h

   #endif
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //

Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h

 // DIGIPOT slave addresses
 //
 #ifndef DIGIPOT_I2C_ADDRESS_A
-  #define DIGIPOT_I2C_ADDRESS_A 0x2C              // unshifted slave address for first DIGIPOT
+  #define DIGIPOT_I2C_ADDRESS_A             0x2C  // unshifted slave address for first DIGIPOT
 #endif
 
 #ifndef DIGIPOT_I2C_ADDRESS_B
-  #define DIGIPOT_I2C_ADDRESS_B 0x2E              // unshifted slave address for second DIGIPOT
+  #define DIGIPOT_I2C_ADDRESS_B             0x2E  // unshifted slave address for second DIGIPOT
 #endif
 
 //

Marlin/src/pins/lpc1769/pins_MKS_SGEN.h

   #define E1_SERIAL_RX_PIN                 P4_28  // J8-6
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif

Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h

   #define E0_SERIAL_RX_PIN                 P0_21
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //

Marlin/src/pins/mega/pins_INTAMSYS40.h

 
 // Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range
 #ifndef MOTOR_CURRENT_PWM_RANGE
-  #define MOTOR_CURRENT_PWM_RANGE  2000
+  #define MOTOR_CURRENT_PWM_RANGE            2000
 #endif
 #define DEFAULT_PWM_MOTOR_CURRENT  { 1300, 1300, 1250 }
 

Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h

 #define DIGIPOTS_I2C_SDA_E1                   77  // J6
 
 #ifndef DIGIPOT_I2C_ADDRESS_A
-  #define DIGIPOT_I2C_ADDRESS_A 0x2F              // unshifted slave address (5E <- 2F << 1)
+  #define DIGIPOT_I2C_ADDRESS_A             0x2F  // unshifted slave address (5E <- 2F << 1)
 #endif
 
 //

Marlin/src/pins/ramps/pins_AZTEEG_X3_PRO.h

 
 // DIGIPOT slave addresses
 #ifndef DIGIPOT_I2C_ADDRESS_A
-  #define DIGIPOT_I2C_ADDRESS_A 0x2C              // unshifted slave address for first DIGIPOT 0x2C (0x58 <- 0x2C << 1)
+  #define DIGIPOT_I2C_ADDRESS_A             0x2C  // unshifted slave address for first DIGIPOT 0x2C (0x58 <- 0x2C << 1)
 #endif
 #ifndef DIGIPOT_I2C_ADDRESS_B
-  #define DIGIPOT_I2C_ADDRESS_B 0x2E              // unshifted slave address for second DIGIPOT 0x2E (0x5C <- 0x2E << 1)
+  #define DIGIPOT_I2C_ADDRESS_B             0x2E  // unshifted slave address for second DIGIPOT 0x2E (0x5C <- 0x2E << 1)
 #endif
 
 //

Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h

 
 #define SUICIDE_PIN                           12  // Used by CR2020 Industrial series
 #ifndef SUICIDE_PIN_INVERTING
-  #define SUICIDE_PIN_INVERTING true
+  #define SUICIDE_PIN_INVERTING             true
 #endif

Marlin/src/pins/sam/pins_PRINTRBOARD_G2.h

 
 #define FET_SAFETY_PIN                        31  // PA7  must be pulsed low every 50 mS or FETs are turned off
 #define FET_SAFETY_DELAY                      50  // 50 mS delay between pulses
-#define FET_SAFETY_INVERTED true                  // true - negative going pulse of 2 uS
+#define FET_SAFETY_INVERTED                 true  // true - negative going pulse of 2 uS
 
 /////////////////////////////////////////////////////////
 

Marlin/src/pins/sam/pins_RADDS.h

 //
 #if EITHER(NO_EEPROM_SELECTED, I2C_EEPROM)
   #define I2C_EEPROM
-  #define MARLIN_EEPROM_SIZE 0x2000               // 8KB
+  #define MARLIN_EEPROM_SIZE              0x2000  // 8KB
 #endif
 
 //

Marlin/src/pins/sam/pins_RAMPS_SMART.h

 
 // I2C EEPROM with 4K of space
 #define I2C_EEPROM
-#define MARLIN_EEPROM_SIZE 0x1000
+#define MARLIN_EEPROM_SIZE                0x1000
 
 #define RESET_PIN                             42  // Resets the board if the jumper is attached
 

Marlin/src/pins/sam/pins_RURAMPS4D_11.h

 //
 // EEPROM
 //
-#define MARLIN_EEPROM_SIZE 0x8000                 // 32Kb (24lc256)
+#define MARLIN_EEPROM_SIZE                0x8000  // 32Kb (24lc256)
 #define I2C_EEPROM                                // EEPROM on I2C-0
 //#define EEPROM_SD                               // EEPROM on SDCARD
 //#define SPI_EEPROM                              // EEPROM on SPI-0

Marlin/src/pins/sam/pins_RURAMPS4D_13.h

 //
 // EEPROM
 //
-#define MARLIN_EEPROM_SIZE 0x8000                 // 32Kb (24lc256)
+#define MARLIN_EEPROM_SIZE                0x8000  // 32Kb (24lc256)
 #define I2C_EEPROM                                // EEPROM on I2C-0
 //#define EEPROM_SD                               // EEPROM on SDCARD
 //#define SPI_EEPROM                              // EEPROM on SPI-0

Marlin/src/pins/samd/pins_RAMPS_144.h

 //
 //#define QSPI_EEPROM                             // Use AGCM4 onboard QSPI EEPROM (Uses 4K of RAM)
 #define I2C_EEPROM                                // EEPROM on I2C-0
-#define MARLIN_EEPROM_SIZE 0x8000                 // 32K (24lc256)
+#define MARLIN_EEPROM_SIZE                0x8000  // 32K (24lc256)
 
 //
 // Limit Switches

Marlin/src/pins/stm32f0/pins_MALYAN_M300.h

 //
 // Timers
 //
-#define STEP_TIMER 6
-#define TEMP_TIMER 7
+#define STEP_TIMER                             6
+#define TEMP_TIMER                             7
 
 //
 // Limit Switches

Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h

 #define DISABLE_JTAG
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
   #define E0_SERIAL_RX_PIN                  PD2
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //
 // USB connect control
 //
 #define USB_CONNECT_PIN                     PC13
-#define USB_CONNECT_INVERTING false
+#define USB_CONNECT_INVERTING              false
 
 /**
  *                 _____
    *
    */
 
-  #define CLCD_SPI_BUS 1                          // SPI1 connector
+  #define CLCD_SPI_BUS                         1  // SPI1 connector
 
   #define BEEPER_PIN                        PB6
 
   #error "SD CUSTOM_CABLE is not compatible with SKR E3 DIP."
 #endif
 
-#define ON_BOARD_SPI_DEVICE 1                     // SPI1
+#define ON_BOARD_SPI_DEVICE                    1  // SPI1
 #define ONBOARD_SD_CS_PIN                   PA4   // Chip select for "System" SD card

Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h

 #define DISABLE_JTAG
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
   #define USB_CONNECT_PIN                   PC13
 #endif
 
-#define USB_CONNECT_INVERTING false
+#define USB_CONNECT_INVERTING              false
 
 /**
  *        SKR Mini E3 V1.0, V1.2                      SKR Mini E3 V2.0
    *
    */
 
-  #define CLCD_SPI_BUS 1                          // SPI1 connector
+  #define CLCD_SPI_BUS                         1  // SPI1 connector
 
   #define BEEPER_PIN                      EXP1_9
 
   #error "SD CUSTOM_CABLE is not compatible with SKR Mini E3."
 #endif
 
-#define ON_BOARD_SPI_DEVICE 1                     // SPI1
+#define ON_BOARD_SPI_DEVICE                    1  // SPI1
 #define ONBOARD_SD_CS_PIN                   PA4   // Chip select for "System" SD card

Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h

 #define DISABLE_JTAG
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
   #define MOSI_PIN                          PA7
   #define SS_PIN                            PA4
 #endif
-#define ON_BOARD_SPI_DEVICE 1                     // SPI1
+#define ON_BOARD_SPI_DEVICE                    1  // SPI1
 #define ONBOARD_SD_CS_PIN                   PA4   // Chip select for "System" SD card

Marlin/src/pins/stm32f1/pins_CCROBOT_MEEB_3DP.h

 //
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
-  #define EEPROM_PAGE_SIZE 0x800U                 // 2KB
+  #define EEPROM_PAGE_SIZE                0x800U  // 2KB
   #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 //
 #define E0_SERIAL_RX_PIN                    PC4
 
 // Reduce baud rate to improve software serial reliability
-#define TMC_BAUD_RATE 19200
+#define TMC_BAUD_RATE                      19200
 
 //
 // Temperature Sensors
   #define SS_PIN                            PA4
 #endif
 
-#define ON_BOARD_SPI_DEVICE 1                     // SPI1
+#define ON_BOARD_SPI_DEVICE                    1  // SPI1
 #define ONBOARD_SD_CS_PIN                   PA4   // Chip select for SD-NAND
 
 #endif

Marlin/src/pins/stm32f1/pins_CHITU3D.h

 //#define I2C_EEPROM
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Steppers

Marlin/src/pins/stm32f1/pins_CHITU3D_V5.h

 
   // Emulated DOGM
 
-  #define GRAPHICAL_TFT_UPSCALE                         3
+  #define GRAPHICAL_TFT_UPSCALE                3
   #ifndef XPT2046_X_CALIBRATION
     #define XPT2046_X_CALIBRATION         -12316
   #endif

Marlin/src/pins/stm32f1/pins_CHITU3D_V6.h

 
 // Emulated DOGM
 #elif ENABLED(FSMC_GRAPHICAL_TFT)
-  #define GRAPHICAL_TFT_UPSCALE                         3
+  #define GRAPHICAL_TFT_UPSCALE                3
 
   #ifndef XPT2046_X_CALIBRATION
     #define XPT2046_X_CALIBRATION         -12316

Marlin/src/pins/stm32f1/pins_CREALITY_V4.h

   #if ENABLED(IIC_BL24CXX_EEPROM)
     #define IIC_EEPROM_SDA                  PA11
     #define IIC_EEPROM_SCL                  PA12
-    #define MARLIN_EEPROM_SIZE 0x800              // 2Kb (24C16)
+    #define MARLIN_EEPROM_SIZE             0x800  // 2Kb (24C16)
   #else
     #define SDCARD_EEPROM_EMULATION               // SD EEPROM until all EEPROM is BL24CXX
-    #define MARLIN_EEPROM_SIZE 0x800              // 2Kb
+    #define MARLIN_EEPROM_SIZE             0x800  // 2Kb
   #endif
 
   // SPI
 //
 #define SD_DETECT_PIN                       PC7
 #define SDCARD_CONNECTION                ONBOARD
-#define ON_BOARD_SPI_DEVICE 1
+#define ON_BOARD_SPI_DEVICE                    1
 #define ONBOARD_SD_CS_PIN                   PA4   // SDSS
 #define SDIO_SUPPORT
 

Marlin/src/pins/stm32f1/pins_FYSETC_AIO_II.h

 #define pins_v2_20190128                          // new pins define
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Flash EEPROM Emulation
 // Stepper current PWM
 //
 #ifndef MOTOR_CURRENT_PWM_RANGE
-  #define MOTOR_CURRENT_PWM_RANGE 1500            // origin:2000
+  #define MOTOR_CURRENT_PWM_RANGE           1500  // origin:2000
 #endif
 #define DEFAULT_PWM_MOTOR_CURRENT { 500, 500, 400 } // origin: {1300,1300,1250}
 
       #define DOGLCD_CS                     PB7
     #endif
 
-    //#define LCD_CONTRAST_INIT 190
+    //#define LCD_CONTRAST_INIT              190
     //#define LCD_SCREEN_ROT_90
     //#define LCD_SCREEN_ROT_180
     //#define LCD_SCREEN_ROT_270

Marlin/src/pins/stm32f1/pins_FYSETC_CHEETAH.h

 // https://github.com/FYSETC/Cheetah
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 #define DISABLE_JTAG
 
   #define LCD_PINS_D4                       PB13  // SCLK
   #define LCD_PINS_ENABLE                   PB15  // DATA MOSI
 
-  //#define LCD_CONTRAST_INIT 190
+  //#define LCD_CONTRAST_INIT                190
 
   #if ENABLED(NEWPANEL)
     #define BTN_EN1                         PC10
     #define CLCD_SOFT_SPI_MISO              PB14
     #define CLCD_SOFT_SPI_SCLK              PB13
   #else
-    #define CLCD_SPI_BUS 2
+    #define CLCD_SPI_BUS                       2
   #endif
 #endif

Marlin/src/pins/stm32f1/pins_GTM32_MINI.h

 //#define DISABLE_JTAGSWD
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 // Enable EEPROM Emulation for this board as it doesn't have EEPROM
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 //
 // ESP WiFi can be soldered to J9 connector which is wired to USART2.
 // Must define WIFISUPPORT in Configuration.h for the printer.
 //
-#define ESP_WIFI_MODULE_COM 2
-#define ESP_WIFI_MODULE_BAUDRATE 115200
+#define ESP_WIFI_MODULE_COM                    2
+#define ESP_WIFI_MODULE_BAUDRATE          115200
 #define ESP_WIFI_MODULE_RESET_PIN           -1

Marlin/src/pins/stm32f1/pins_GTM32_MINI_A30.h

 //#define DISABLE_JTAGSWD
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 // Enable EEPROM Emulation for this board as it doesn't have EEPROM
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 //
 // ESP WiFi can be soldered to J9 connector which is wired to USART2.
 // Must define WIFISUPPORT in Configuration.h for the printer.
 //
-#define ESP_WIFI_MODULE_COM 2
-#define ESP_WIFI_MODULE_BAUDRATE 115200
+#define ESP_WIFI_MODULE_COM                    2
+#define ESP_WIFI_MODULE_BAUDRATE          115200
 #define ESP_WIFI_MODULE_RESET_PIN           -1

Marlin/src/pins/stm32f1/pins_GTM32_PRO_VB.h

 //#define DISABLE_JTAGSWD
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 // Enable EEPROM Emulation for this board as it doesn't have EEPROM
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 //
 // ESP WiFi can be soldered to J9 connector which is wired to USART2.
 // Must define WIFISUPPORT in Configuration.h for the printer.
 //
-#define ESP_WIFI_MODULE_COM 2
-#define ESP_WIFI_MODULE_BAUDRATE 115200
+#define ESP_WIFI_MODULE_COM                    2
+#define ESP_WIFI_MODULE_BAUDRATE          115200
 #define ESP_WIFI_MODULE_RESET_PIN           -1

Marlin/src/pins/stm32f1/pins_GTM32_REV_B.h

 //#define DISABLE_JTAGSWD
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 // Enable EEPROM Emulation for this board as it doesn't have EEPROM
 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
   #define FLASH_EEPROM_EMULATION
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 //
 // ESP WiFi can be soldered to J9 connector which is wired to USART2.
 // Must define WIFISUPPORT in Configuration.h for the printer.
 //
-#define ESP_WIFI_MODULE_COM 2
-#define ESP_WIFI_MODULE_BAUDRATE 115200
+#define ESP_WIFI_MODULE_COM                    2
+#define ESP_WIFI_MODULE_BAUDRATE          115200
 #define ESP_WIFI_MODULE_RESET_PIN           -1

Marlin/src/pins/stm32f1/pins_JGAURORA_A5S_A1.h

 // Enable EEPROM Emulation for this board, so that we don't overwrite factory data
 
 //#define I2C_EEPROM                              // AT24C64
-//#define MARLIN_EEPROM_SIZE 0x8000UL             // 64KB
+//#define MARLIN_EEPROM_SIZE            0x8000UL  // 64KB
 
 //#define FLASH_EEPROM_EMULATION
-//#define MARLIN_EEPROM_SIZE 0x1000UL             // 4KB
+//#define MARLIN_EEPROM_SIZE            0x1000UL  // 4KB
 //#define MARLIN_EEPROM_SIZE (EEPROM_START_ADDRESS + (EEPROM_PAGE_SIZE) * 2UL)
 
 //#define EEPROM_CHITCHAT

Marlin/src/pins/stm32f1/pins_LONGER3D_LK.h

 #define DOGLCD_MOSI                         -1    // Prevent auto-define by Conditionals_post.h
 #define DOGLCD_SCK                          -1
 
-#define GRAPHICAL_TFT_UPSCALE                           2
+#define GRAPHICAL_TFT_UPSCALE                  2
 #define TFT_WIDTH                            320
 #define TFT_HEIGHT                           240
 #define TFT_PIXEL_OFFSET_X                    32

Marlin/src/pins/stm32f1/pins_MALYAN_M200.h

 // On STM32F103:
 // PB3, PB6, PB7, and PB8 can be used with pwm, which rules out TIM2 and TIM4.
 // On STM32F070, 16 and 17 are in use, but 1 and 3 are available.
-#define STEP_TIMER 1
-#define TEMP_TIMER 3
+#define STEP_TIMER                             1
+#define TEMP_TIMER                             3
 
 //
 // Limit Switches

Marlin/src/pins/stm32f1/pins_MKS_ROBIN.h

 
   // Reduce baud rate for software serial reliability
   #if HAS_TMC_SW_SERIAL
-    #define TMC_BAUD_RATE 19200
+    #define TMC_BAUD_RATE                  19200
   #endif
 #endif

Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h

   #define E0_SERIAL_RX_PIN                  PC11
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //

Marlin/src/pins/stm32f1/pins_MKS_ROBIN_MINI.h

 #define E0_STEP_PIN                         PD6
 #define E0_DIR_PIN                          PD3
 
-
 // Motor current PWM pins
 #define MOTOR_CURRENT_PWM_XY_PIN            PA6
 #define MOTOR_CURRENT_PWM_Z_PIN             PA7
 #define SERVO0_PIN                          PA8   // Enable BLTOUCH support on IO0 (WIFI connector)
 
 #define MT_DET_1_PIN                        PA4
-#define MT_DET_PIN_INVERTING false
+#define MT_DET_PIN_INVERTING               false
 
 #define WIFI_IO0_PIN                        PC13
 
   #define FSMC_CS_PIN                       PD7   // NE4
   #define FSMC_RS_PIN                       PD11  // A0
 
-  #define LCD_USE_DMA_FSMC                  // Use DMA transfers to send data to the TFT
+  #define LCD_USE_DMA_FSMC                        // Use DMA transfers to send data to the TFT
   #define FSMC_DMA_DEV                      DMA2
-  #define FSMC_DMA_CHANNEL                  DMA_CH5
+  #define FSMC_DMA_CHANNEL               DMA_CH5
 
   #define LCD_RESET_PIN                     PC6   // FSMC_RST
   #define LCD_BACKLIGHT_PIN                 PD13
     #define TOUCH_MOSI_PIN                  PB15  // SPI2_MOSI
   #endif
 
-#elif ENABLED(TFT_320x240) //TFT32/28
+#elif ENABLED(TFT_320x240)                        //TFT32/28
 
   #define TFT_RESET_PIN                     PC6
   #define TFT_BACKLIGHT_PIN                 PD13
   #define ILI9341_COLOR_RGB
 #endif
 
-#define HAS_SPI_FLASH 1
+#define HAS_SPI_FLASH                          1
 #define SPI_FLASH_SIZE                 0x1000000  // 16MB
 #if HAS_SPI_FLASH
   #define W25QXX_CS_PIN                     PB12  // Flash chip-select

Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO.h

   #define FSMC_DMA_CHANNEL               DMA_CH5
 
   #define TOUCH_BUTTONS_HW_SPI
-  #define TOUCH_BUTTONS_HW_SPI_DEVICE       2
+  #define TOUCH_BUTTONS_HW_SPI_DEVICE          2
 #endif
 
 // LVGL Configs
   #define DOGLCD_SCK                        -1
 
   #ifndef GRAPHICAL_TFT_UPSCALE
-    #define GRAPHICAL_TFT_UPSCALE                       3
+    #define GRAPHICAL_TFT_UPSCALE              3
   #endif
   #ifndef TFT_WIDTH
     #define TFT_WIDTH                        480

Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h

   #endif
 
   #ifndef GRAPHICAL_TFT_UPSCALE
-    #define GRAPHICAL_TFT_UPSCALE                       3
+    #define GRAPHICAL_TFT_UPSCALE              3
   #endif
   #ifndef TFT_PIXEL_OFFSET_Y
     #define TFT_PIXEL_OFFSET_Y                32

Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h

 //
 // Note: MKS Robin board is using SPI2 interface.
 //
-//#define SPI_MODULE 2
+//#define SPI_MODULE                           2
 #define ENABLE_SPI2
 
 //

Marlin/src/pins/stm32f1/pins_STM32F1R.h

 #define DEFAULT_MACHINE_NAME "STM32F103RET6"
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Limit Switches
 #if HAS_SPI_LCD
 
   #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-    #define LCD_PINS_RS 49                        // CS chip select /SS chip slave select
-    #define LCD_PINS_ENABLE 51                    // SID (MOSI)
-    #define LCD_PINS_D4 52                        // SCK (CLK) clock
+    #define LCD_PINS_RS                       49  // CS chip select /SS chip slave select
+    #define LCD_PINS_ENABLE                   51  // SID (MOSI)
+    #define LCD_PINS_D4                       52  // SCK (CLK) clock
   #elif BOTH(NEWPANEL, PANEL_ONE)
     #define LCD_PINS_RS                     PB8
     #define LCD_PINS_ENABLE                 PD2
     #define LCD_PINS_D6                     PB14
     #define LCD_PINS_D7                     PB15
     #if DISABLED(NEWPANEL)
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
       // Buttons attached to a shift register
       // Not wired yet
-      //#define SHIFT_CLK 38
-      //#define SHIFT_LD 42
-      //#define SHIFT_OUT 40
-      //#define SHIFT_EN 17
+      //#define SHIFT_CLK                     38
+      //#define SHIFT_LD                      42
+      //#define SHIFT_OUT                     40
+      //#define SHIFT_EN                      17
     #endif
   #endif
 
 
     #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
 
-      #define BEEPER_PIN 37
+      #define BEEPER_PIN                      37
 
-      #define BTN_EN1 31
-      #define BTN_EN2 33
-      #define BTN_ENC 35
+      #define BTN_EN1                         31
+      #define BTN_EN2                         33
+      #define BTN_ENC                         35
 
-      #define SD_DETECT_PIN 49
-      #define KILL_PIN 41
+      #define SD_DETECT_PIN                   49
+      #define KILL_PIN                        41
 
       #if ENABLED(BQ_LCD_SMART_CONTROLLER)
-        #define LCD_BACKLIGHT_PIN 39
+        #define LCD_BACKLIGHT_PIN             39
       #endif
 
     #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
 
-      #define BTN_EN1 64
-      #define BTN_EN2 59
-      #define BTN_ENC 63
-      #define SD_DETECT_PIN 42
+      #define BTN_EN1                         64
+      #define BTN_EN2                         59
+      #define BTN_ENC                         63
+      #define SD_DETECT_PIN                   42
 
     #elif ENABLED(LCD_I2C_PANELOLU2)
 
-      #define BTN_EN1 47
-      #define BTN_EN2 43
-      #define BTN_ENC 32
-      #define LCD_SDSS 53
+      #define BTN_EN1                         47
+      #define BTN_EN2                         43
+      #define BTN_ENC                         32
+      #define LCD_SDSS                        53
       #define SD_DETECT_PIN                 -1
-      #define KILL_PIN 41
+      #define KILL_PIN                        41
 
     #elif ENABLED(LCD_I2C_VIKI)
 
-      #define BTN_EN1 22                          // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
-      #define BTN_EN2 7                           // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
+      #define BTN_EN1                         22  // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
+      #define BTN_EN2                          7  // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
 
       #define BTN_ENC                       -1
-      #define LCD_SDSS 53
-      #define SD_DETECT_PIN 49
+      #define LCD_SDSS                        53
+      #define SD_DETECT_PIN                   49
 
     #elif ANY(VIKI2, miniVIKI)
 
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
 
       // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0 44
-      #define DOGLCD_CS 45
+      #define DOGLCD_A0                       44
+      #define DOGLCD_CS                       45
       #define LCD_SCREEN_ROT_180
 
-      #define BTN_EN1 22
-      #define BTN_EN2 7
-      #define BTN_ENC 39
+      #define BTN_EN1                         22
+      #define BTN_EN2                          7
+      #define BTN_ENC                         39
 
-      #define SDSS 53
+      #define SDSS                            53
       #define SD_DETECT_PIN                 -1    // Pin 49 for display sd interface, 72 for easy adapter board
 
-      #define KILL_PIN 31
+      #define KILL_PIN                        31
 
-      #define STAT_LED_RED_PIN 32
-      #define STAT_LED_BLUE_PIN 35
+      #define STAT_LED_RED_PIN                32
+      #define STAT_LED_BLUE_PIN               35
 
     #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
-      #define BTN_EN1 35
-      #define BTN_EN2 37
-      #define BTN_ENC 31
-      #define SD_DETECT_PIN 49
-      #define LCD_SDSS 53
-      #define KILL_PIN 41
-      #define BEEPER_PIN 23
-      #define DOGLCD_CS 29
-      #define DOGLCD_A0 27
-      #define LCD_BACKLIGHT_PIN 33
+      #define BTN_EN1                         35
+      #define BTN_EN2                         37
+      #define BTN_ENC                         31
+      #define SD_DETECT_PIN                   49
+      #define LCD_SDSS                        53
+      #define KILL_PIN                        41
+      #define BEEPER_PIN                      23
+      #define DOGLCD_CS                       29
+      #define DOGLCD_A0                       27
+      #define LCD_BACKLIGHT_PIN               33
 
     #elif ENABLED(MINIPANEL)
 
-      #define BEEPER_PIN 42
+      #define BEEPER_PIN                      42
       // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0 44
-      #define DOGLCD_CS 66
-      #define LCD_BACKLIGHT_PIN 65                // backlight LED on A11/D65
-      #define SDSS 53
+      #define DOGLCD_A0                       44
+      #define DOGLCD_CS                       66
+      #define LCD_BACKLIGHT_PIN               65  // backlight LED on A11/D65
+      #define SDSS                            53
 
-      #define KILL_PIN 64
+      #define KILL_PIN                        64
       // GLCD features
       // Uncomment screen orientation
       //#define LCD_SCREEN_ROT_90
       //#define LCD_SCREEN_ROT_180
       //#define LCD_SCREEN_ROT_270
       // The encoder and click button
-      #define BTN_EN1 40
-      #define BTN_EN2 63
-      #define BTN_ENC 59
+      #define BTN_EN1                         40
+      #define BTN_EN2                         63
+      #define BTN_ENC                         59
       // not connected to a pin
-      #define SD_DETECT_PIN 49
+      #define SD_DETECT_PIN                   49
 
     #else
 
       // Beeper on AUX-4
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
 
       // Buttons directly attached to AUX-2
       #if ENABLED(REPRAPWORLD_KEYPAD)
-        #define BTN_EN1 64
-        #define BTN_EN2 59
-        #define BTN_ENC 63
-        #define SHIFT_OUT 40
-        #define SHIFT_CLK 44
-        #define SHIFT_LD 42
+        #define BTN_EN1                       64
+        #define BTN_EN2                       59
+        #define BTN_ENC                       63
+        #define SHIFT_OUT                     40
+        #define SHIFT_CLK                     44
+        #define SHIFT_LD                      42
       #elif ENABLED(PANEL_ONE)
-        #define BTN_EN1 59                        // AUX2 PIN 3
-        #define BTN_EN2 63                        // AUX2 PIN 4
-        #define BTN_ENC 49                        // AUX3 PIN 7
+        #define BTN_EN1                       59  // AUX2 PIN 3
+        #define BTN_EN2                       63  // AUX2 PIN 4
+        #define BTN_ENC                       49  // AUX3 PIN 7
       #else
-        #define BTN_EN1 37
-        #define BTN_EN2 35
-        #define BTN_ENC 31
+        #define BTN_EN1                       37
+        #define BTN_EN2                       35
+        #define BTN_ENC                       31
       #endif
 
       #if ENABLED(G3D_PANEL)
-        #define SD_DETECT_PIN 49
-        #define KILL_PIN 41
+        #define SD_DETECT_PIN                 49
+        #define KILL_PIN                      41
       #else
         //#define SD_DETECT_PIN             -1    // Ramps doesn't use this
       #endif

Marlin/src/pins/stm32f1/pins_STM3R_MINI.h

 #define I2C_EEPROM
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Limit Switches
 #if HAS_SPI_LCD
 
   #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-    #define LCD_PINS_RS 49                        // CS chip select /SS chip slave select
-    #define LCD_PINS_ENABLE 51                    // SID (MOSI)
-    #define LCD_PINS_D4 52                        // SCK (CLK) clock
+    #define LCD_PINS_RS                       49  // CS chip select /SS chip slave select
+    #define LCD_PINS_ENABLE                   51  // SID (MOSI)
+    #define LCD_PINS_D4                       52  // SCK (CLK) clock
   #elif BOTH(NEWPANEL, PANEL_ONE)
     #define LCD_PINS_RS                     PB8
     #define LCD_PINS_ENABLE                 PD2
     #define LCD_PINS_D6                     PB14
     #define LCD_PINS_D7                     PB15
     #if DISABLED(NEWPANEL)
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
       // Buttons attached to a shift register
       // Not wired yet
-      //#define SHIFT_CLK 38
-      //#define SHIFT_LD 42
-      //#define SHIFT_OUT 40
-      //#define SHIFT_EN 17
+      //#define SHIFT_CLK                     38
+      //#define SHIFT_LD                      42
+      //#define SHIFT_OUT                     40
+      //#define SHIFT_EN                      17
     #endif
   #endif
 
 
     #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
 
-      #define BEEPER_PIN 37
+      #define BEEPER_PIN                      37
 
-      #define BTN_EN1 31
-      #define BTN_EN2 33
-      #define BTN_ENC 35
+      #define BTN_EN1                         31
+      #define BTN_EN2                         33
+      #define BTN_ENC                         35
 
-      #define SD_DETECT_PIN 49
-      #define KILL_PIN 41
+      #define SD_DETECT_PIN                   49
+      #define KILL_PIN                        41
 
       #if ENABLED(BQ_LCD_SMART_CONTROLLER)
-        #define LCD_BACKLIGHT_PIN 39
+        #define LCD_BACKLIGHT_PIN             39
       #endif
 
     #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
 
-      #define BTN_EN1 64
-      #define BTN_EN2 59
-      #define BTN_ENC 63
-      #define SD_DETECT_PIN 42
+      #define BTN_EN1                         64
+      #define BTN_EN2                         59
+      #define BTN_ENC                         63
+      #define SD_DETECT_PIN                   42
 
     #elif ENABLED(LCD_I2C_PANELOLU2)
 
-      #define BTN_EN1 47
-      #define BTN_EN2 43
-      #define BTN_ENC 32
-      #define LCD_SDSS 53
+      #define BTN_EN1                         47
+      #define BTN_EN2                         43
+      #define BTN_ENC                         32
+      #define LCD_SDSS                        53
       #define SD_DETECT_PIN                 -1
-      #define KILL_PIN 41
+      #define KILL_PIN                        41
 
     #elif ENABLED(LCD_I2C_VIKI)
 
-      #define BTN_EN1 22                          // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
-      #define BTN_EN2 7                           // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
+      #define BTN_EN1                         22  // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
+      #define BTN_EN2                          7  // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
 
       #define BTN_ENC                       -1
-      #define LCD_SDSS 53
-      #define SD_DETECT_PIN 49
+      #define LCD_SDSS                        53
+      #define SD_DETECT_PIN                   49
 
     #elif ANY(VIKI2, miniVIKI)
 
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
 
       // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0 44
-      #define DOGLCD_CS 45
+      #define DOGLCD_A0                       44
+      #define DOGLCD_CS                       45
       #define LCD_SCREEN_ROT_180
 
-      #define BTN_EN1 22
-      #define BTN_EN2 7
-      #define BTN_ENC 39
+      #define BTN_EN1                         22
+      #define BTN_EN2                          7
+      #define BTN_ENC                         39
 
-      #define SDSS 53
+      #define SDSS                            53
       #define SD_DETECT_PIN                 -1    // Pin 49 for display sd interface, 72 for easy adapter board
 
-      #define KILL_PIN 31
+      #define KILL_PIN                        31
 
-      #define STAT_LED_RED_PIN 32
-      #define STAT_LED_BLUE_PIN 35
+      #define STAT_LED_RED_PIN                32
+      #define STAT_LED_BLUE_PIN               35
 
     #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
 
-      #define BTN_EN1 35
-      #define BTN_EN2 37
-      #define BTN_ENC 31
-      #define SD_DETECT_PIN 49
-      #define LCD_SDSS 53
-      #define KILL_PIN 41
-      #define BEEPER_PIN 23
-      #define DOGLCD_CS 29
-      #define DOGLCD_A0 27
-      #define LCD_BACKLIGHT_PIN 33
+      #define BTN_EN1                         35
+      #define BTN_EN2                         37
+      #define BTN_ENC                         31
+      #define SD_DETECT_PIN                   49
+      #define LCD_SDSS                        53
+      #define KILL_PIN                        41
+      #define BEEPER_PIN                      23
+      #define DOGLCD_CS                       29
+      #define DOGLCD_A0                       27
+      #define LCD_BACKLIGHT_PIN               33
 
     #elif ENABLED(MINIPANEL)
 
-      #define BEEPER_PIN 42
+      #define BEEPER_PIN                      42
       // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0 44
-      #define DOGLCD_CS 66
-      #define LCD_BACKLIGHT_PIN 65                // backlight LED on A11/D65
-      #define SDSS 53
+      #define DOGLCD_A0                       44
+      #define DOGLCD_CS                       66
+      #define LCD_BACKLIGHT_PIN               65  // backlight LED on A11/D65
+      #define SDSS                            53
 
-      #define KILL_PIN 64
+      #define KILL_PIN                        64
       // GLCD features
       // Uncomment screen orientation
       //#define LCD_SCREEN_ROT_90
       //#define LCD_SCREEN_ROT_180
       //#define LCD_SCREEN_ROT_270
       // The encoder and click button
-      #define BTN_EN1 40
-      #define BTN_EN2 63
-      #define BTN_ENC 59
+      #define BTN_EN1                         40
+      #define BTN_EN2                         63
+      #define BTN_ENC                         59
       // not connected to a pin
-      #define SD_DETECT_PIN 49
+      #define SD_DETECT_PIN                   49
 
     #else
 
       // Beeper on AUX-4
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
 
       // Buttons directly attached to AUX-2
       #if ENABLED(REPRAPWORLD_KEYPAD)
-        #define BTN_EN1 64
-        #define BTN_EN2 59
-        #define BTN_ENC 63
-        #define SHIFT_OUT 40
-        #define SHIFT_CLK 44
-        #define SHIFT_LD 42
+        #define BTN_EN1                       64
+        #define BTN_EN2                       59
+        #define BTN_ENC                       63
+        #define SHIFT_OUT                     40
+        #define SHIFT_CLK                     44
+        #define SHIFT_LD                      42
       #elif ENABLED(PANEL_ONE)
-        #define BTN_EN1 59                        // AUX2 PIN 3
-        #define BTN_EN2 63                        // AUX2 PIN 4
-        #define BTN_ENC 49                        // AUX3 PIN 7
+        #define BTN_EN1                       59  // AUX2 PIN 3
+        #define BTN_EN2                       63  // AUX2 PIN 4
+        #define BTN_ENC                       49  // AUX3 PIN 7
       #else
-        #define BTN_EN1 37
-        #define BTN_EN2 35
-        #define BTN_ENC 31
+        #define BTN_EN1                       37
+        #define BTN_EN2                       35
+        #define BTN_ENC                       31
       #endif
 
       #if ENABLED(G3D_PANEL)
-        #define SD_DETECT_PIN 49
-        #define KILL_PIN 41
+        #define SD_DETECT_PIN                 49
+        #define KILL_PIN                      41
       #else
         //#define SD_DETECT_PIN             -1    // Ramps doesn't use this
       #endif

Marlin/src/pins/stm32f1/pins_TRIGORILLA_PRO.h

 //
 #define HEATER_0_PIN                        PG12  // HEATER1
 #define HEATER_BED_PIN                      PG11  // HOT BED
-#define HEATER_BED_INVERTING true
+#define HEATER_BED_INVERTING                true
 
 //
 // Fans

Marlin/src/pins/stm32f4/pins_ARMED.h

 #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
 
 #define I2C_EEPROM
-#define MARLIN_EEPROM_SIZE 0x1000                 // 4KB
+#define MARLIN_EEPROM_SIZE                0x1000  // 4KB
 
 //
 // Limit Switches
   #define Z2_SERIAL_RX_PIN              EXT4_PIN
   #define Z2_SERIAL_TX_PIN              EXT4_PIN
 
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif

Marlin/src/pins/stm32f4/pins_BEAST.h

 #define I2C_EEPROM
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Steppers
 #if HAS_SPI_LCD
 
   #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-    #define LCD_PINS_RS 49                        // CS chip select /SS chip slave select
-    #define LCD_PINS_ENABLE 51                    // SID (MOSI)
-    #define LCD_PINS_D4 52                        // SCK (CLK) clock
+    #define LCD_PINS_RS                       49  // CS chip select /SS chip slave select
+    #define LCD_PINS_ENABLE                   51  // SID (MOSI)
+    #define LCD_PINS_D4                       52  // SCK (CLK) clock
   #elif BOTH(NEWPANEL, PANEL_ONE)
     #define LCD_PINS_RS                     PB8
     #define LCD_PINS_ENABLE                 PD2
     #define LCD_PINS_D6                     PB14
     #define LCD_PINS_D7                     PB15
     #if DISABLED(NEWPANEL)
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
       // Buttons attached to a shift register
       // Not wired yet
-      //#define SHIFT_CLK 38
-      //#define SHIFT_LD 42
-      //#define SHIFT_OUT 40
-      //#define SHIFT_EN 17
+      //#define SHIFT_CLK                     38
+      //#define SHIFT_LD                      42
+      //#define SHIFT_OUT                     40
+      //#define SHIFT_EN                      17
     #endif
   #endif
 
 
     #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
 
-      #define BEEPER_PIN 37
+      #define BEEPER_PIN                      37
 
-      #define BTN_EN1 31
-      #define BTN_EN2 33
-      #define BTN_ENC 35
+      #define BTN_EN1                         31
+      #define BTN_EN2                         33
+      #define BTN_ENC                         35
 
-      #define SD_DETECT_PIN 49
-      #define KILL_PIN 41
+      #define SD_DETECT_PIN                   49
+      #define KILL_PIN                        41
 
       #if ENABLED(BQ_LCD_SMART_CONTROLLER)
-        #define LCD_BACKLIGHT_PIN 39
+        #define LCD_BACKLIGHT_PIN             39
       #endif
 
     #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
 
-      #define BTN_EN1 64
-      #define BTN_EN2 59
-      #define BTN_ENC 63
-      #define SD_DETECT_PIN 42
+      #define BTN_EN1                         64
+      #define BTN_EN2                         59
+      #define BTN_ENC                         63
+      #define SD_DETECT_PIN                   42
 
     #elif ENABLED(LCD_I2C_PANELOLU2)
 
-      #define BTN_EN1 47
-      #define BTN_EN2 43
-      #define BTN_ENC 32
-      #define LCD_SDSS 53
+      #define BTN_EN1                         47
+      #define BTN_EN2                         43
+      #define BTN_ENC                         32
+      #define LCD_SDSS                        53
       #define SD_DETECT_PIN                 -1
-      #define KILL_PIN 41
+      #define KILL_PIN                        41
 
     #elif ENABLED(LCD_I2C_VIKI)
 
-      #define BTN_EN1 22                          // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
-      #define BTN_EN2 7                           // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
+      #define BTN_EN1                         22  // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
+      #define BTN_EN2                          7  // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
 
       #define BTN_ENC                       -1
-      #define LCD_SDSS 53
-      #define SD_DETECT_PIN 49
+      #define LCD_SDSS                        53
+      #define SD_DETECT_PIN                   49
 
     #elif ANY(VIKI2, miniVIKI)
 
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
 
       // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0 44
-      #define DOGLCD_CS 45
+      #define DOGLCD_A0                       44
+      #define DOGLCD_CS                       45
       #define LCD_SCREEN_ROT_180
 
-      #define BTN_EN1 22
-      #define BTN_EN2 7
-      #define BTN_ENC 39
+      #define BTN_EN1                         22
+      #define BTN_EN2                          7
+      #define BTN_ENC                         39
 
-      #define SDSS 53
+      #define SDSS                            53
       #define SD_DETECT_PIN                 -1    // Pin 49 for display sd interface, 72 for easy adapter board
 
-      #define KILL_PIN 31
+      #define KILL_PIN                        31
 
-      #define STAT_LED_RED_PIN 32
-      #define STAT_LED_BLUE_PIN 35
+      #define STAT_LED_RED_PIN                32
+      #define STAT_LED_BLUE_PIN               35
 
     #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
 
-      #define BTN_EN1 35
-      #define BTN_EN2 37
-      #define BTN_ENC 31
-      #define SD_DETECT_PIN 49
-      #define LCD_SDSS 53
-      #define KILL_PIN 41
-      #define BEEPER_PIN 23
-      #define DOGLCD_CS 29
-      #define DOGLCD_A0 27
-      #define LCD_BACKLIGHT_PIN 33
+      #define BTN_EN1                         35
+      #define BTN_EN2                         37
+      #define BTN_ENC                         31
+      #define SD_DETECT_PIN                   49
+      #define LCD_SDSS                        53
+      #define KILL_PIN                        41
+      #define BEEPER_PIN                      23
+      #define DOGLCD_CS                       29
+      #define DOGLCD_A0                       27
+      #define LCD_BACKLIGHT_PIN               33
 
     #elif ENABLED(MINIPANEL)
 
-      #define BEEPER_PIN 42
+      #define BEEPER_PIN                      42
       // Pins for DOGM SPI LCD Support
-      #define DOGLCD_A0 44
-      #define DOGLCD_CS 66
-      #define LCD_BACKLIGHT_PIN 65                // backlight LED on A11/D65
-      #define SDSS 53
+      #define DOGLCD_A0                       44
+      #define DOGLCD_CS                       66
+      #define LCD_BACKLIGHT_PIN               65  // backlight LED on A11/D65
+      #define SDSS                            53
 
-      #define KILL_PIN 64
+      #define KILL_PIN                        64
       // GLCD features
       // Uncomment screen orientation
       //#define LCD_SCREEN_ROT_90
       //#define LCD_SCREEN_ROT_180
       //#define LCD_SCREEN_ROT_270
       // The encoder and click button
-      #define BTN_EN1 40
-      #define BTN_EN2 63
-      #define BTN_ENC 59
+      #define BTN_EN1                         40
+      #define BTN_EN2                         63
+      #define BTN_ENC                         59
       // not connected to a pin
-      #define SD_DETECT_PIN 49
+      #define SD_DETECT_PIN                   49
 
     #else
 
       // Beeper on AUX-4
-      #define BEEPER_PIN 33
+      #define BEEPER_PIN                      33
 
       // Buttons directly attached to AUX-2
       #if ENABLED(REPRAPWORLD_KEYPAD)
-        #define BTN_EN1 64
-        #define BTN_EN2 59
-        #define BTN_ENC 63
-        #define SHIFT_OUT 40
-        #define SHIFT_CLK 44
-        #define SHIFT_LD 42
+        #define BTN_EN1                       64
+        #define BTN_EN2                       59
+        #define BTN_ENC                       63
+        #define SHIFT_OUT                     40
+        #define SHIFT_CLK                     44
+        #define SHIFT_LD                      42
       #elif ENABLED(PANEL_ONE)
-        #define BTN_EN1 59                        // AUX2 PIN 3
-        #define BTN_EN2 63                        // AUX2 PIN 4
-        #define BTN_ENC 49                        // AUX3 PIN 7
+        #define BTN_EN1                       59  // AUX2 PIN 3
+        #define BTN_EN2                       63  // AUX2 PIN 4
+        #define BTN_ENC                       49  // AUX3 PIN 7
       #else
-        #define BTN_EN1 37
-        #define BTN_EN2 35
-        #define BTN_ENC 31
+        #define BTN_EN1                       37
+        #define BTN_EN2                       35
+        #define BTN_ENC                       31
       #endif
 
       #if ENABLED(G3D_PANEL)
-        #define SD_DETECT_PIN 49
-        #define KILL_PIN 41
+        #define SD_DETECT_PIN                 49
+        #define KILL_PIN                      41
       #else
         //#define SD_DETECT_PIN             -1    // Ramps doesn't use this
       #endif

Marlin/src/pins/stm32f4/pins_BLACK_STM32F407VE.h

 
 //#define I2C_EEPROM
 #define SRAM_EEPROM_EMULATION
-#define MARLIN_EEPROM_SIZE 0x2000                 // 8KB
+#define MARLIN_EEPROM_SIZE                0x2000  // 8KB
 
 //
 // Servos

Marlin/src/pins/stm32f4/pins_BTT_BTT002_V1_0.h

 #endif
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Limit Switches
   #define E0_SERIAL_RX_PIN                  PD7
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //

Marlin/src/pins/stm32f4/pins_BTT_GTR_V1_0.h

 
 // Onboard I2C EEPROM
 #define I2C_EEPROM
-#define MARLIN_EEPROM_SIZE 0x2000                 // 8KB (24C64 ... 64Kb = 8KB)
+#define MARLIN_EEPROM_SIZE                0x2000  // 8KB (24C64 ... 64Kb = 8KB)
 
 #define TP                                        // Enable to define servo and probe pins
 
   #define E7_SERIAL_RX_PIN                  PH14
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //

Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h

   #define E2_SERIAL_RX_PIN                  PD6
 
   // Reduce baud rate to improve software serial reliability
-  #define TMC_BAUD_RATE 19200
+  #define TMC_BAUD_RATE                    19200
 #endif
 
 //
  *           ￣￣
  *            W1
  */
-#define ESP_WIFI_MODULE_COM 6                     // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
+#define ESP_WIFI_MODULE_COM                    6  // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
 #define ESP_WIFI_MODULE_BAUDRATE        BAUDRATE  // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
 #define ESP_WIFI_MODULE_RESET_PIN           PG0
 #define ESP_WIFI_MODULE_ENABLE_PIN          PG1

Marlin/src/pins/stm32f4/pins_FLYF407ZG.h

   // the 128kB sector allocated for EEPROM emulation.
   #define FLASH_EEPROM_LEVELING
 #elif ENABLED(I2C_EEPROM)
-  #define MARLIN_EEPROM_SIZE 0x2000               // 8KB
+  #define MARLIN_EEPROM_SIZE              0x2000  // 8KB
 #endif
 
 #ifndef MARLIN_EEPROM_SIZE
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 //

Marlin/src/pins/stm32f4/pins_FYSETC_S6.h

 #endif
 
 // Change the priority to 3. Priority 2 is for software serial.
-//#define TEMP_TIMER_IRQ_PRIO 3
+//#define TEMP_TIMER_IRQ_PRIO                  3
 
 //
 // EEPROM Emulation
   // 128 kB sector allocated for EEPROM emulation.
   #define FLASH_EEPROM_LEVELING
 #elif ENABLED(I2C_EEPROM)
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 //

Marlin/src/pins/stm32f4/pins_GENERIC_STM32F4.h

 //#define I2C_EEPROM
 
 #ifndef MARLIN_EEPROM_SIZE
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Limit Switches

Marlin/src/pins/stm32f4/pins_LERDGE_K.h

 // Misc. Functions
 //
 #define SDSS                                PC11
-#define LED_PIN                             PA15   // Alive
+#define LED_PIN                             PA15  // Alive
 #define PS_ON_PIN                           -1
 #define KILL_PIN                            -1
-#define POWER_LOSS_PIN                      PA4    // Power-loss / nAC_FAULT
+#define POWER_LOSS_PIN                      PA4   // Power-loss / nAC_FAULT
 
 #define SCK_PIN                             PC12
 #define MISO_PIN                            PC8

Marlin/src/pins/stm32f4/pins_LERDGE_S.h

 #define BOARD_INFO_NAME      "Lerdge S"
 #define DEFAULT_MACHINE_NAME "LERDGE"
 
-#define STEP_TIMER 4
-#define TEMP_TIMER 2
+#define STEP_TIMER                             4
+#define TEMP_TIMER                             2
 
 //#define I2C_EEPROM
 
 
 #if ENABLED(SPI_EEPROM)
   // Lerdge has an SPI EEPROM Winbond W25Q128 (128Mbits) https://www.pjrc.com/teensy/W25Q128FV.pdf
-  #define SPI_CHAN_EEPROM1 1
+  #define SPI_CHAN_EEPROM1                     1
   #define SPI_EEPROM1_CS                    PB12  // datasheet: /CS pin, found with multimeter, not tested
   #define EEPROM_SCK                        PB13  // datasheet: CLK pin, found with multimeter, not tested
   #define EEPROM_MISO                       PB14  // datasheet: DO pin, found with multimeter, not tested
   #define EEPROM_MOSI                       PB15  // datasheet: DI pin, found with multimeter, not tested
-  #define EEPROM_PAGE_SIZE 0x1000U                // 4KB (from datasheet)
+  #define EEPROM_PAGE_SIZE               0x1000U  // 4KB (from datasheet)
   #define MARLIN_EEPROM_SIZE 16UL * (EEPROM_PAGE_SIZE)   // Limit to 64KB for now...
 #else
-  #define MARLIN_EEPROM_SIZE 0x800U               // On SD, Limit to 2KB, require this amount of RAM
+  #define MARLIN_EEPROM_SIZE              0x800U  // On SD, Limit to 2KB, require this amount of RAM
 #endif
 
 //

Marlin/src/pins/stm32f4/pins_LERDGE_X.h

 #define BOARD_INFO_NAME      "Lerdge X"
 #define DEFAULT_MACHINE_NAME "LERDGE"
 
-#define STEP_TIMER 4
-#define TEMP_TIMER 2
+#define STEP_TIMER                             4
+#define TEMP_TIMER                             2
 
 #define I2C_EEPROM
 
 #define KILL_PIN                            -1
 
 // Lerdge supports auto-power off and power loss sense through a single pin.
-#define POWER_LOSS_PIN                      PC14    // Power-loss / nAC_FAULT
+#define POWER_LOSS_PIN                      PC14  // Power-loss / nAC_FAULT
 
 #define SCK_PIN                             PC12
 #define MISO_PIN                            PC8

Marlin/src/pins/stm32f4/pins_RUMBA32_AUS3D.h

 #if NO_EEPROM_SELECTED
   #if MB(RUMBA32_V1_0)
     #define FLASH_EEPROM_EMULATION
-    #define MARLIN_EEPROM_SIZE 0x1000             // 4KB
+    #define MARLIN_EEPROM_SIZE            0x1000  // 4KB
   #elif MB(RUMBA32_V1_1)
     #define I2C_EEPROM
-    #define MARLIN_EEPROM_SIZE 0x2000             // 8KB (24LC64T-I/OT)
+    #define MARLIN_EEPROM_SIZE            0x2000  // 8KB (24LC64T-I/OT)
   #endif
 #endif
 

Marlin/src/pins/stm32f4/pins_RUMBA32_MKS.h

 
 #if NO_EEPROM_SELECTED
   #define FLASH_EEPROM_EMULATION
-  #define MARLIN_EEPROM_SIZE 0x1000               // 4KB
+  #define MARLIN_EEPROM_SIZE              0x1000  // 4KB
 #endif
 
 #if ENABLED(FLASH_EEPROM_EMULATION)

Marlin/src/pins/stm32f4/pins_RUMBA32_common.h

 // TIM7 is used for SERVO
 // TIMER_SERIAL defaults to TIM7 so we'll override it here
 //
-#define STEP_TIMER 10
-#define TEMP_TIMER 14
+#define STEP_TIMER                            10
+#define TEMP_TIMER                            14
 #define TIMER_SERIAL                        TIM9
 #define HAL_TIMER_RATE                     F_CPU
 

Marlin/src/pins/stm32f4/pins_VAKE403D.h

 #define BOARD_INFO_NAME      "STM32F4 VAkE"
 
 //#define I2C_EEPROM
-#define MARLIN_EEPROM_SIZE 0x1000                 // 4KB
+#define MARLIN_EEPROM_SIZE                0x1000  // 4KB
 
 //
 // Servos

Marlin/src/pins/stm32f7/pins_THE_BORG.h

 #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
 
 #ifndef MARLIN_EEPROM_SIZE
-  #define MARLIN_EEPROM_SIZE 0x1000
+  #define MARLIN_EEPROM_SIZE              0x1000
 #endif
 
 // Ignore temp readings during development.
-//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
 
 //
 // Limit Switches

Marlin/src/pins/teensy2/pins_5DPRINT.h

 
 //DIGIPOTS slave addresses
 #ifndef DIGIPOT_I2C_ADDRESS_A
-  #define DIGIPOT_I2C_ADDRESS_A 0x2C              // unshifted slave address for DIGIPOT 0x2C (0x58 <- 0x2C << 1)
+  #define DIGIPOT_I2C_ADDRESS_A             0x2C  // unshifted slave address for DIGIPOT 0x2C (0x58 <- 0x2C << 1)
 #endif

Marlin/src/pins/teensy2/pins_PRINTRBOARD_REVF.h

 #define DAC_STEPPER_MAX                      3520
 #define DAC_STEPPER_VREF                       1  // internal Vref, gain 1x = 2.048V
 #define DAC_STEPPER_GAIN                       0
-#define DAC_OR_ADDRESS 0x00
+#define DAC_OR_ADDRESS                      0x00
 
 //
 // Temperature Sensors