Adjust some config comments

Marlin/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

Marlin/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/default/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/default/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/3DFabXYZ/Migbot/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/AlephObjects/TAZ4/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AlephObjects/TAZ4/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/AliExpress/CL-260/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AliExpress/UM2pExt/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AliExpress/UM2pExt/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A2/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A2/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A2plus/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A2plus/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A6/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A6/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A8/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A8/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/A8plus/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/A8plus/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Anet/E16/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Anet/E16/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/AnyCubic/i3/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/AnyCubic/i3/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/ArmEd/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/ArmEd/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Azteeg/X5GT/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BIBO/TouchX/cyclops/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BIBO/TouchX/default/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BIBO/TouchX/default/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BQ/Hephestos/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BQ/Hephestos/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BQ/Hephestos_2/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
 
   // Set one or more commands to execute on filament runout.

config/examples/BQ/Hephestos_2/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 300
 #define DISABLE_INACTIVE_X false
 #define DISABLE_INACTIVE_Y false
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/BQ/WITBOX/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/BQ/WITBOX/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Cartesio/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Cartesio/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/CR-10/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10S/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING true // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
   #define FIL_RUNOUT_PIN 2 // Creality CR10-S stock sensor

config/examples/Creality/CR-10S/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10_5S/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
   #define FIL_RUNOUT_PIN 2 // Creality CR10-S stock sensor

config/examples/Creality/CR-10_5S/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-10mini/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/CR-10mini/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/CR-8/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/CR-8/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/Ender-2/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/Ender-2/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/Ender-3/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/Ender-3/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Creality/Ender-4/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Creality/Ender-4/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Dagoma/Disco Ultimate/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Einstart-S/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-//#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-//#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-//#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-//#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+//#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+//#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+//#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+//#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 #define X_STOP_INVERTING true
 #define Y_STOP_INVERTING true
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Einstart-S/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Felix/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Felix/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 60
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Felix/DUAL/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/FlashForge/CreatorPro/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/FlashForge/CreatorPro/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z false  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z false  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/FolgerTech/i3-2020/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/FolgerTech/i3-2020/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Formbot/Raptor/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN 57
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Formbot/Raptor/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Formbot/T_Rex_2+/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 600
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Formbot/T_Rex_3/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
   #ifndef NUM_RUNOUT_SENSORS
     #define NUM_RUNOUT_SENSORS   1
   #endif
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Formbot/T_Rex_3/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 600
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/A10/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN      66
   //#define FIL_RUNOUT2_PIN     67
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensors.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/A10/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/A10M/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
   #define NUM_RUNOUT_SENSORS   2     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN      66
   #define FIL_RUNOUT2_PIN     67
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensors.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/A10M/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/A20M/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
   #define NUM_RUNOUT_SENSORS   2     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN      66
   #define FIL_RUNOUT2_PIN     67
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors.
+  #define FIL_RUNOUT_INVERTING true  // Set to true to invert the logic of the sensors.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/A20M/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/GT2560/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/MeCreator2/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/MeCreator2/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/Infitary/i3-M508/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Infitary/i3-M508/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/JGAurora/A1/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/JGAurora/A1/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/JGAurora/A5/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 #define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/JGAurora/A5/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power

config/examples/JGAurora/A5S/Configuration.h

 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/JGAurora/A5S/Configuration_adv.h

 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
-#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_Z true  // Set to false if the nozzle will fall down on your printed part when print has finished.
 #define DISABLE_INACTIVE_E true
 
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
   // Define pin which is read during calibration
   #ifndef CALIBRATION_PIN
     #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
-    #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
 //#define SPINDLE_LASER_ENABLE
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
+  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
+  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
+  #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
+  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
+  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
   #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
 
   /**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power