Apply MOVE_Z_WHEN_IDLE to example configurations

Co-Authored-By: dot-bob <gibben@gmail.com>

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Anet/A2/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Cartesio/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Einstart-S/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Felix/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Formbot/Raptor/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   #define BABYSTEP_ZPROBE_OFFSET            // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     #define BABYSTEP_HOTEND_Z_OFFSET        // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/MakerParts/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/RigidBot/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/SCARA/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/TheBorg/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/delta/generic/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/makibox/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets

Marlin/src/config/examples/wt150/Configuration_adv.h

                                             // Note: Extra time may be added to mitigate controller latency.
   #endif
 
+  //#define MOVE_Z_WHEN_IDLE                // Jump to the move Z menu on doubleclick when printer is idle.
+  #if ENABLED(MOVE_Z_WHEN_IDLE)
+    #define MOVE_Z_IDLE_MULTIPLICATOR 1     // Multiply 1mm by this factor for the move step size.
+  #endif
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets