Tweak some config comments

Marlin/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/default/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/default/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Anet/A2/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Anet/A2/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Anet/A2plus/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Anet/A6/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

   //#define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Anet/A8/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

   //#define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT  8  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT  8  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                             // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 10  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 10  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 3  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 3  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE false         // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "G27 P0"      // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "G27 P0"      // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Cartesio/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Cartesio/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Creality/CR-10/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 5  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 5  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 4    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 4    // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 5  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 5  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Creality/CR-8/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Creality/Ender-2/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Creality/Ender-3/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Creality/Ender-4/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Einstart-S/Configuration.h

 
 #define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Einstart-S/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Felix/Configuration.h

 //=============================================================================
 // @section motion
 
-// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
+// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 Z error.
 /**
  * Default Settings
  *
 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Felix/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Felix/DUAL/Configuration.h

 //=============================================================================
 // @section motion
 
-// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
+// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 Z error.
 /**
  * Default Settings
  *
 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 2    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 2    // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Formbot/Raptor/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Formbot/Raptor/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 8    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 8    // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 8    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 8    // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 8  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 8  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/JGAurora/A5/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/MakerParts/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/MakerParts/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Malyan/M150/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Malyan/M200/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Mks/Sbase/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h

  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  */
-#define DEFAULT_MAX_Z_FEEDRATE        3.3 // older Huxley has problem with speeds > 3.3 mm/s on z axis
+#define DEFAULT_MAX_Z_FEEDRATE        3.3 // older Huxley has problem with speeds > 3.3 mm/s on Z axis
 #define DEFAULT_MAX_FEEDRATE          { 200, 200, DEFAULT_MAX_Z_FEEDRATE, 25 }
 
 /**
 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 4    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 4    // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/RigidBot/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/RigidBot/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/SCARA/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/SCARA/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/STM32F10/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/STM32F4/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Sanguinololu/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 4    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 4    // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/TheBorg/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/TheBorg/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/TinyBoy2/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Tronxy/X1/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Tronxy/X3A/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

Marlin/src/config/examples/Tronxy/X5S/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 10 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/Tronxy/XY100/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                            // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

 
 //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.