Update Bed PID comments

Marlin/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/default/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 206 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Anet/A6/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Anet/A8/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 #define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Cartesio/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Creality/CR-10/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Creality/CR-8/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Creality/Ender-2/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Creality/Ender-4/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Felix/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Felix/DUAL/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/JGAurora/A5/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/MakerParts/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Malyan/M150/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Malyan/M200/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Mks/Sbase/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/RigidBot/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/SCARA/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/STM32F10/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Sanguinololu/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/TheBorg/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/TinyBoy2/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Tronxy/X1/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Tronxy/X5S/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Tronxy/XY100/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Velleman/K8200/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Velleman/K8400/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/generic/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 #define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/makibox/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 175 // limits duty cycle to bed; 255=full current
 // This limit is set to 175 by default in the Makibox configuration and it can be adjusted
 // to increase the heatup rate. However, if changed, be aware of the safety concerns of

Marlin/src/config/examples/stm32f103ret6/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)

Marlin/src/config/examples/wt150/Configuration.h

 //===========================================================================
 //============================= PID > Bed Temperature Control ===============
 //===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
 //#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)