Merge pull request #7134 from thinkyhead/bf_skynet_a3_ready

Add Skynet/ANET A10 support

Marlin/Conditionals_LCD.h

   #define LCD_HAS_DIRECTIONAL_BUTTONS (BUTTON_EXISTS(UP) || BUTTON_EXISTS(DWN) || BUTTON_EXISTS(LFT) || BUTTON_EXISTS(RT))
 
   #if ENABLED(CARTESIO_UI)
+
     #define DOGLCD
     #define ULTIPANEL
     #define NEWPANEL
     #define DEFAULT_LCD_CONTRAST 90
     #define LCD_CONTRAST_MIN 60
     #define LCD_CONTRAST_MAX 140
-  #endif
 
-  #if ENABLED(MAKRPANEL) || ENABLED(MINIPANEL)
+  #elif ENABLED(MAKRPANEL) || ENABLED(MINIPANEL)
+
     #define DOGLCD
     #define ULTIPANEL
     #define NEWPANEL
     #define DEFAULT_LCD_CONTRAST 17
-  #endif
 
-  #if ENABLED(miniVIKI) || ENABLED(VIKI2) || ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
+  #elif ENABLED(ANET_KEYPAD_LCD)
+
+    #define REPRAPWORLD_KEYPAD
+    #define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
+    #define ADC_KEYPAD
+    #define ADC_KEY_NUM 8
+    #define ULTIPANEL
+    // this helps to implement ADC_KEYPAD menus
+    #define ENCODER_STEPS_PER_MENU_ITEM 1
+    #define REVERSE_MENU_DIRECTION
+
+  #elif ENABLED(ANET_FULL_GRAPHICS_LCD)
+
+    #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+  #elif ENABLED(BQ_LCD_SMART_CONTROLLER)
+
+    #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+    #define LONG_FILENAME_HOST_SUPPORT
+
+  #elif ENABLED(miniVIKI) || ENABLED(VIKI2) || ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
+
     #define ULTRA_LCD  //general LCD support, also 16x2
     #define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
     #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
       #define SD_DETECT_INVERTED
     #endif
 
-  #endif
+  #elif ENABLED(OLED_PANEL_TINYBOY2)
 
-  #if ENABLED(OLED_PANEL_TINYBOY2)
     #define U8GLIB_SSD1306
     #define ULTIPANEL
     #define NEWPANEL
     #define REVERSE_ENCODER_DIRECTION
     #define REVERSE_MENU_DIRECTION
+
+  #elif ENABLED(RA_CONTROL_PANEL)
+
+    #define LCD_I2C_TYPE_PCA8574
+    #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
+    #define ULTIPANEL
+    #define NEWPANEL
+
+  #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
+
+    #define DOGLCD
+    #define U8GLIB_ST7920
+    #define ULTIPANEL
+    #define NEWPANEL
+
   #endif
 
   // Generic support for SSD1306 / SH1106 OLED based LCDs.
     #define ULTIMAKERCONTROLLER
   #endif
 
-  #if ENABLED(BQ_LCD_SMART_CONTROLLER)
-    #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
-    #ifndef LONG_FILENAME_HOST_SUPPORT
-      #define LONG_FILENAME_HOST_SUPPORT
-    #endif
-  #endif
-
   #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
     #define DOGLCD
     #define U8GLIB_ST7920
     #endif
   #endif
 
-  #if ENABLED(RA_CONTROL_PANEL)
-    #define LCD_I2C_TYPE_PCA8574
-    #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
-    #define ULTIPANEL
-    #define NEWPANEL
-  #endif
-
-  #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
-    #define DOGLCD
-    #define U8GLIB_ST7920
-    #define ULTIPANEL
-    #define NEWPANEL
-  #endif
-
   /**
    * I2C PANELS
    */
 
   #if ENABLED(LCD_I2C_SAINSMART_YWROBOT)
+
     // Note: This controller requires F.Malpartida's LiquidCrystal_I2C library
     // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
+
     #define LCD_I2C_TYPE_PCF8575
     #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
     #define ULTIPANEL
     #define NEWPANEL
-  #endif
 
-  // PANELOLU2 LCD with status LEDs, separate encoder and click inputs
-  #if ENABLED(LCD_I2C_PANELOLU2)
+  #elif ENABLED(LCD_I2C_PANELOLU2)
+
+    // PANELOLU2 LCD with status LEDs, separate encoder and click inputs
+
     #define LCD_I2C_TYPE_MCP23017
     #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
     #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
     #define ULTIPANEL
     #define NEWPANEL
-  #endif
 
-  // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
-  #if ENABLED(LCD_I2C_VIKI)
-    // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
-    // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
-    // Note: The pause/stop/resume LCD button pin should be connected to the Arduino
-    //       BTN_ENC pin (or set BTN_ENC to -1 if not used)
+  #elif ENABLED(LCD_I2C_VIKI)
+
+    /**
+     * Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
+     *
+     * This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+     * Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+     * Note: The pause/stop/resume LCD button pin should be connected to the Arduino
+     *       BTN_ENC pin (or set BTN_ENC to -1 if not used)
+     */
     #define LCD_I2C_TYPE_MCP23017
     #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
     #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)

Marlin/SanityCheck.h

   #if ENABLED(MINIPANEL)
     + 1
   #endif
-  #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI)
+  #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI) && DISABLED(ANET_KEYPAD_LCD)
     + 1
   #endif
   #if ENABLED(RIGIDBOT_PANEL)
   #if ENABLED(OLED_PANEL_TINYBOY2)
     + 1
   #endif
+  #if ENABLED(ANET_KEYPAD_LCD)
+    + 1
+  #endif
   , "Please select no more than one LCD controller option."
 );
 

Marlin/boards.h

 #define BOARD_MELZI_MAKR3D      66   // Melzi with ATmega1284 (MaKr3d version)
 #define BOARD_AZTEEG_X3         67   // Azteeg X3
 #define BOARD_AZTEEG_X3_PRO     68   // Azteeg X3 Pro
+#define BOARD_ANET_10           69   // Anet 1.0 (Melzi clone)
 #define BOARD_ULTIMAKER         7    // Ultimaker
 #define BOARD_ULTIMAKER_OLD     71   // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
 #define BOARD_ULTIMAIN_2        72   // Ultimainboard 2.x (Uses TEMP_SENSOR 20)

Marlin/example_configurations/CL-260/Configuration.h

  * Probe Type
  *
  * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
- * You must activate one of these to use Auto Bed Leveling below.
+ * Activate one of these to use Auto Bed Leveling below.
  */
 
 /**
 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/Cartesio/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/Cartesio/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/Felix/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/Felix/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/Felix/DUAL/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/FolgerTech-i3-2020/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/Hephestos/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/Hephestos/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/Hephestos_2/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 #define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/K8200/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD

Marlin/example_configurations/K8200/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/K8400/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/K8400/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/K8400/Dual-head/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/M150/Configuration.h

  * Probe Type
  *
  * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
- * You must activate one of these to use Auto Bed Leveling below.
+ * Activate one of these to use Auto Bed Leveling below.
  */
 
 /**
 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/M150/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/RigidBot/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/RigidBot/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/SCARA/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/SCARA/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/TAZ4/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/TAZ4/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/TinyBoy2/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD

Marlin/example_configurations/TinyBoy2/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/WITBOX/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/WITBOX/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/adafruit/ST7565/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/delta/generic/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/delta/generic/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/delta/kossel_mini/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/delta/kossel_pro/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/delta/kossel_xl/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/gCreate_gMax1.5+/Configuration.h

 //#define Z_MIN_PROBE_ENDSTOP
 
 /**
- *   Probe Type
+ * Probe Type
  *
- *   Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
- *   You must activate one of these to use Auto Bed Leveling below.
+ * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
+ * Activate one of these to use Auto Bed Leveling below.
  */
 
 /**
 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/gCreate_gMax1.5+/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/makibox/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/makibox/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/tvrrug/Round2/Configuration.h

 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/example_configurations/wt150/Configuration.h

  * Probe Type
  *
  * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
- * You must activate one of these to use Auto Bed Leveling below.
+ * Activate one of these to use Auto Bed Leveling below.
  */
 
 /**
 //#define ULTIPANEL
 
 //
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
 //
 //#define BQ_LCD_SMART_CONTROLLER
 
 //
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD         // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
 // CONTROLLER TYPE: I2C
 //
 // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
 //#define U8GLIB_SSD1306
 
 //
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
 // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
 //
 //#define SAV_3DGLCD
 //
 //#define SAV_3DLCD
 
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
 //=============================================================================
 //=============================== Extra Features ==============================
 //=============================================================================

Marlin/example_configurations/wt150/Configuration_adv.h

   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-//Show Temperature ADC value
-//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
 
 /**

Marlin/pins.h

   #include "pins_AZTEEG_X3.h"
 #elif MB(AZTEEG_X3_PRO)
   #include "pins_AZTEEG_X3_PRO.h"
+#elif MB(ANET_10)
+  #include "pins_ANET_10.h"
 #elif MB(ULTIMAKER)
   #include "pins_ULTIMAKER.h"
 #elif MB(ULTIMAKER_OLD)

Marlin/pinsDebug.h

   bool get_pinMode(int8_t pin) {return *portModeRegister(digitalPinToPort_DEBUG(pin)) & digitalPinToBitMask_DEBUG(pin); }
 #endif
 
+#if defined(__AVR_ATmega1284P__)  // 1284 IDE extensions set this to the number of
+  #undef NUM_DIGITAL_PINS         // digital only pins while all other CPUs have it
+  #define NUM_DIGITAL_PINS 32     // set to digital only + digital/analog
+#endif
+
 #define PWM_PRINT(V) do{ sprintf_P(buffer, PSTR("PWM:  %4d"), V); SERIAL_ECHO(buffer); }while(0)
 #define PWM_CASE(N,Z)                                           \
   case TIMER##N##Z:                                             \

Marlin/pinsDebug_list.h

 
 #line 0 // set __LINE__ to a known value for both passes
 
+#if PIN_EXISTS(ADC_KEYPAD) && ADC_KEYPAD_PIN < NUM_ANALOG_INPUTS
+  REPORT_NAME_ANALOG(ADC_KEYPAD_PIN, __LINE__ )
+#endif
 #if defined(__FD) && __FD >= 0
   REPORT_NAME_DIGITAL(__FD, __LINE__ )
 #endif

Marlin/pins_ANET_10.h

+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Anet V1.0 board pin assignments
+ */
+
+/**
+ * Rev B    16 JUN 2017
+ *
+ * 1) no longer uses Sanguino files to define some of the pins
+ * 2) added pointers to useable Arduino IDE extensions
+ *
+ */
+
+/**
+ * The standard Arduino IDE extension (board manager) for this board
+ * is located at https://github.com/SkyNet3D/anet-board.
+ *
+ * Installation instructions are on that page.
+ *
+ * After copying the files to the appropriate location, restart Arduino and
+ * you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list.
+ *
+ * "Anet V1.0" uses the bootloader that was installed on the board when
+ * it shipped from the factory.
+ *
+ * "Anet V1.0 (Optiboot)" frees up another 3K of FLASH.  You'll need to burn
+ * a new bootloader to the board to be able to automatically download a
+ * compiled image.
+ *
+ */
+
+/**
+ * Another usable Arduino IDE extension (board manager) can be found at
+ * https://github.com/Lauszus/Sanguino
+ *
+ * This extension has been tested on Arduino 1.6.12 & 1.8.0
+ *
+ * Here's the JSON path:
+ * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
+ *
+ * When installing select 1.0.2
+ *
+ * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
+ * Just use the above JSON URL instead of Sparkfun's JSON.
+ *
+ * Once installed select the Sanguino board and then select the CPU.
+ *
+ */
+
+/**
+ *  To burn a new bootloader:
+ *
+ *   1. Connect your programmer to the board.
+ *   2. In the Arduino IDE select the board and then select the programmer.
+ *   3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
+ *   4. The programmer is no longer needed. Remove it.
+ */
+
+/**
+ * Additional info:
+ *
+ *   Anet Schematics                    - https://github.com/ralf-e/ANET-3D-Board-V1.0
+ *   Wiring RRDFG Smart Controller      - http://www.thingiverse.com/thing:2103748
+ *   SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/
+ *   Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/
+ *
+ *   Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community.
+*/
+
+#if !defined(__AVR_ATmega1284P__)
+  #error "Oops!  Make sure you have 'Anet V1.0', 'Anet V1.0 (Optiboot)' or 'Sanguino' selected from the 'Tools -> Boards' menu."
+#endif
+
+#ifndef BOARD_NAME
+  #define BOARD_NAME "Anet"
+#endif
+
+#define LARGE_FLASH true
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN         18
+#define Y_STOP_PIN         19
+#define Z_STOP_PIN         20
+
+//
+// Steppers
+//
+#define X_STEP_PIN         15
+#define X_DIR_PIN          21
+#define X_ENABLE_PIN       14
+
+#define Y_STEP_PIN         22
+#define Y_DIR_PIN          23
+#define Y_ENABLE_PIN       14
+
+#define Z_STEP_PIN          3
+#define Z_DIR_PIN           2
+#define Z_ENABLE_PIN       26
+
+#define E0_STEP_PIN         1
+#define E0_DIR_PIN          0
+#define E0_ENABLE_PIN      14
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN          7  // Analog Input (pin 33 extruder)
+#define TEMP_BED_PIN        6  // Analog Input (pin 34 bed)
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN       13  // (extruder)
+#define HEATER_BED_PIN     12  // (bed)
+#define FAN_PIN             4
+
+//
+// Misc. Functions
+//
+#define SDSS               31
+#define LED_PIN            -1
+
+/**
+ * LCD / Controller
+ *
+ * Only the following displays are supported:
+ *  ANET_KEYPAD_LCD
+ *  ANET_FULL_GRAPHICS_LCD
+ *  REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+*/
+
+#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
+  #define LCD_SDSS           28
+  #if ENABLED(ADC_KEYPAD)
+    #define SERVO0_PIN         27 // free for BLTouch/3D-Touch
+    #define LCD_PINS_RS        28
+    #define LCD_PINS_ENABLE    29
+    #define LCD_PINS_D4        10
+    #define LCD_PINS_D5        11
+    #define LCD_PINS_D6        16
+    #define LCD_PINS_D7        17
+    #define BTN_EN1            -1
+    #define BTN_EN2            -1
+    #define BTN_ENC            -1
+    #define ADC_KEYPAD_PIN      1
+    #define ENCODER_FEEDRATE_DEADZONE 2
+  #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) || ENABLED(ANET_FULL_GRAPHICS_LCD)
+    // Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics
+    // display using an adapter board  // https://go.aisler.net/benlye/anet-lcd-adapter/pcb
+    // See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748
+    #define SERVO0_PIN         29 // free for BLTouch/3D-Touch
+    #define BEEPER_PIN         17
+    #define LCD_PINS_RS        27
+    #define LCD_PINS_ENABLE    28
+    #define LCD_PINS_D4        30
+    #define BTN_EN1            11
+    #define BTN_EN2            10
+    #define BTN_ENC            16
+    #define ST7920_DELAY_1 DELAY_0_NOP
+    #define ST7920_DELAY_2 DELAY_1_NOP
+    #define ST7920_DELAY_3 DELAY_2_NOP
+    #ifndef ENCODER_STEPS_PER_MENU_ITEM
+      #define ENCODER_STEPS_PER_MENU_ITEM 1
+    #endif
+    #ifndef ENCODER_PULSES_PER_STEP
+      #define ENCODER_PULSES_PER_STEP 4
+    #endif
+  #endif
+#endif  // ULTRA_LCD && NEWPANEL
+
+/**
+ * ====================================================================
+ * =============== Alternative RepRapDiscount Wiring ==================
+ * ====================================================================
+ *
+ * An alternative wiring scheme for the RepRapDiscount Full Graphics Display is
+ * published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748.
+ *
+ * Using that adapter requires changing the pin definition as follows:
+ *   #define SERVO0_PIN        27 // free for BLTouch/3D-Touch
+ *   #define BEEPER_PIN        28
+ *   #define LCD_PINS_RS       30
+ *   #define LCD_PINS_ENABLE   29
+ *   #define LCD_PINS_D4       17
+ *
+ * The BLTouch pin becomes LCD:3
+ */
+
+/**
+ * ====================================================================
+ * ===================== LCD PINOUTS ==================================
+ * ====================================================================
+ *
+ *   Anet V1.0 controller           | ANET_KEYPAD_LCD   | ANET_FULL_      | RepRapDiscount Full      | Thingiverse RepRap wiring
+ *   physical   logical   alt       |                   | GRAPHICS_LCD    | Graphics Display Wiring  | http://www.thingiverse
+ *     pin        pin     functions |                   |                 |                          | .com/thing:2103748
+ *------------------------------------------------------------------------------------------------------------------------
+ *   ANET-J3.1    8 ***             | N/A               | J3_TX ***       |                          |
+ *   ANET-J3.2    9 ***             | N/A               | J3_RX ***       |                          |
+ *   ANET-J3.3    6       MISO      | N/A               | MISO ***        | EXP2.1   MISO            | EXP2.1   MISO
+ *   ANET-J3.4    +5V               | N/A               | +5V             |                          |
+ *   ANET-J3.5    7       SCK       | N/A               | SCK ***         | EXP2.2   SCK             | EXP2.2   SCK
+ *   ANET-J3.6    5       MOSI      | N/A               | MOSI ***        | EXP2.6   MOSI            | EXP2.6   MOSI
+ *   ANET-J3.7    !RESET            | N/A               | button          | EXP2.8   panel button    | EXP2.8   panel button
+ *   ANET-J3.8    GND               | N/A               | GND             | EXP2.9   GND             | EXP2.9   GND
+ *   ANET-J3.9    4       Don't use | N/A               | N/C             |                          |
+ *   ANET-J3.10   +3.3V             | N/A               | +3.3V ***       |                          |
+ *                                  |                   |                 |                          |
+ *                                  |                   |                 |                          |
+ *   ANET-LCD.1   GND               | GND               | GND             | EXP1.9   GND             | EXP1.9   GND
+ *   ANET-LCD.2   +5V               | +5V               | +5V             | EXP1.10  +5V             | EXP1.10  +5V
+ *   ANET-LCD.3   27      A4        | N/C *             | LCD_PINS_RS     | EXP1.4   LCD_PINS_RS     | EXP2.4   SDSS or N/C *
+ *   ANET-LCD.4   10                | LCD_PINS_D4       | BTN_EN2         | EXP2.3   BTN_EN2         | EXP2.3   BTN_EN2
+ *   ANET-LCD.5   28      A3        | LCD_PINS_RS       | LCD_PINS_ENABLE | EXP1.3   LCD_PINS_ENABLE | EXP1.1   BEEPER_PIN
+ *   ANET-LCD.6   11                | LCD_PINS_D5       | BTN_EN1         | EXP2.5   BTN_EN1         | EXP2.5   BTN_EN1
+ *   ANET-LCD.7   29      A2        | LCD_PINS_ENABLE   | N/C *           | EXP2.4   SDSS or N/C *   | EXP1.3   LCD_PINS_ENABLE
+ *   ANET-LCD.8   16      SCL       | LCD_PINS_D6       | BTN_ENC         | EXP1.2   BTN_ENC         | EXP1.2   BTN_ENC
+ *   ANET-LCD.9   30      A1        | ADC_KEYPAD_PIN ** | LCD_PINS_D4     | EXP1.5   LCD_PINS_D4     | EXP1.4   LCD_PINS_RS
+ *   ANET-LCD.10  17      SDA       | LCD_PINS_D7       | BEEPER_PIN      | EXP1.1   BEEPER_PIN      | EXP1.5   LCD_PINS_D4
+ *
+ *                 N/C * - if not connected to the LCD can be used for BLTouch servo input
+ *                 ** - analog pin -WITHOUT a pullup
+ *                 *** - only connected to something if the Bluetooth module is populated
+ */
+
+/**
+ *   REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+ *   physical pin  function
+ *   EXP1.1        BEEPER
+ *   EXP1.2        BTN_ENC
+ *   EXP1.3        LCD_PINS_ENABLE
+ *   EXP1.4        LCD_PINS_RS
+ *   EXP1.5        LCD_PINS_D4
+ *   EXP1.6        LCD_PINS_D5 (not used)
+ *   EXP1.7        LCD_PINS_D6 (not used)
+ *   EXP1.8        LCD_PINS_D7 (not used)
+ *   EXP1.9        GND
+ *   EXP1.10       VCC
+ *
+ *
+ *   EXP2.1        MISO
+ *   EXP2.2        SCK
+ *   EXP2.3        BTN_EN2
+ *   EXP2.4        SDSS
+ *   EXP2.5        BTN_EN1
+ *   EXP2.6        MOSI
+ *   EXP2.7        SD_DETECT_PIN
+ *   EXP2.8        button
+ *   EXP2.9        GND
+ *   EXP2.10       NC
+ */

Marlin/temperature.cpp

   #endif
 #endif
 
+#if ENABLED(ADC_KEYPAD)
+  uint32_t Temperature::current_ADCKey_raw = 0;
+  uint8_t Temperature::ADCKey_count = 0;
+#endif
+
 #if HAS_PID_HEATING
 
   void Temperature::PID_autotune(float temp, int hotend, int ncycles, bool set_result/*=false*/) {
   static uint8_t pwm_count = _BV(SOFT_PWM_SCALE);
   // avoid multiple loads of pwm_count
   uint8_t pwm_count_tmp = pwm_count;
+  #if ENABLED(ADC_KEYPAD)
+    static unsigned int raw_ADCKey_value = 0;
+  #endif
 
   // Static members for each heater
   #if ENABLED(SLOW_PWM_HEATERS)
           raw_filwidth_value -= (raw_filwidth_value >> 7); // Subtract 1/128th of the raw_filwidth_value
           raw_filwidth_value += ((unsigned long)ADC << 7); // Add new ADC reading, scaled by 128
         }
-        break;
+      break;
     #endif
 
+    #if ENABLED(ADC_KEYPAD)
+      case Prepare_ADC_KEY:
+        START_ADC(ADC_KEYPAD_PIN);
+        break;
+      case Measure_ADC_KEY:
+        if (ADCKey_count < 16) {
+          raw_ADCKey_value = ADC;
+          if (raw_ADCKey_value > 900) {
+            //ADC Key release
+            ADCKey_count = 0;
+            current_ADCKey_raw = 0;
+          }
+          else {
+            current_ADCKey_raw += raw_ADCKey_value;
+            ADCKey_count++;
+          }
+        }
+        break;
+    #endif // ADC_KEYPAD
+
     case StartupDelay: break;
 
   } // switch(adc_sensor_state)

Marlin/temperature.h

     Prepare_FILWIDTH,
     Measure_FILWIDTH,
   #endif
+  #if ENABLED(ADC_KEYPAD)
+    Prepare_ADC_KEY,
+    Measure_ADC_KEY,
+  #endif
   SensorsReady, // Temperatures ready. Delay the next round of readings to let ADC pins settle.
   StartupDelay  // Startup, delay initial temp reading a tiny bit so the hardware can settle
 };
     #endif
 
   public:
+    #if ENABLED(ADC_KEYPAD)
+      static uint32_t current_ADCKey_raw;
+      static uint8_t ADCKey_count;
+    #endif
 
     /**
      * Instance Methods

Marlin/ultralcd.cpp

 
   /**
    *
-   * Handlers for RepRap World Keypad input
+   * Handlers for Keypad input
    *
    */
-  #if ENABLED(REPRAPWORLD_KEYPAD)
+  #if ENABLED(ADC_KEYPAD)
+
+    inline void handle_adc_keypad() {
+      static uint8_t adc_steps = 0;
+      if (buttons_reprapworld_keypad) {
+        adc_steps++;
+        NOMORE(adc_steps, 20);
+
+        lcd_quick_feedback();
+        lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
+        return_to_status_ms = millis() + LCD_TIMEOUT_TO_STATUS;
+        if (encoderDirection == -1) { // side effect which signals we are inside a menu
+          if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_DOWN)
+            encoderPosition -= ENCODER_STEPS_PER_MENU_ITEM;
+          else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_UP)
+            encoderPosition += ENCODER_STEPS_PER_MENU_ITEM;
+          else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_LEFT)
+            menu_action_back();
+          else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_RIGHT)
+            // enqueue_and_echo_commands_P(PSTR("M0 Pause"));
+            lcd_return_to_status();
+        }
+        else {
+          const int8_t step = adc_steps > 19 ? 100 : adc_steps > 10 ? 10 : 1;
+          if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_DOWN)
+            encoderPosition += ENCODER_PULSES_PER_STEP * step;
+          else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_UP)
+            encoderPosition -= ENCODER_PULSES_PER_STEP * step;
+          else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_RIGHT)
+            encoderPosition = 0;
+        }
+        #if ENABLED(ADC_KEYPAD_DEBUG)
+          SERIAL_PROTOCOLLNPAIR("buttons_reprapworld_keypad = ", (uint32_t)buttons_reprapworld_keypad);
+          SERIAL_PROTOCOLLNPAIR("encoderPosition = ", (uint32_t)encoderPosition);
+        #endif
+      }
+      else if (!thermalManager.current_ADCKey_raw) {
+        // reset stepping acceleration
+        adc_steps = 0;
+      }
+    }
+
+  #elif ENABLED(REPRAPWORLD_KEYPAD)
+
     void _reprapworld_keypad_move(const AxisEnum axis, const int16_t dir) {
       move_menu_scale = REPRAPWORLD_KEYPAD_MOVE_STEP;
       encoderPosition = dir;
       SET_INPUT_PULLUP(BTN_ENC);
     #endif
 
-    #if ENABLED(REPRAPWORLD_KEYPAD)
+    #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(ADC_KEYPAD)
       SET_OUTPUT(SHIFT_CLK);
       OUT_WRITE(SHIFT_LD, HIGH);
       SET_INPUT_PULLUP(SHIFT_OUT);
         slow_buttons = lcd_implementation_read_slow_buttons(); // buttons which take too long to read in interrupt context
       #endif
 
-      #if ENABLED(REPRAPWORLD_KEYPAD)
+      #if ENABLED(ADC_KEYPAD)
+
+        handle_adc_keypad();
+
+      #elif ENABLED(REPRAPWORLD_KEYPAD)
+
         handle_reprapworld_keypad();
+
       #endif
 
       bool encoderPastThreshold = (abs(encoderDiff) >= ENCODER_PULSES_PER_STEP);
             if (encoderRateMultiplierEnabled) {
               int32_t encoderMovementSteps = abs(encoderDiff) / ENCODER_PULSES_PER_STEP;
 
-              if (lastEncoderMovementMillis != 0) {
+              if (lastEncoderMovementMillis) {
                 // Note that the rate is always calculated between two passes through the
                 // loop and that the abs of the encoderDiff value is tracked.
-                float encoderStepRate = (float)(encoderMovementSteps) / ((float)(ms - lastEncoderMovementMillis)) * 1000.0;
+                float encoderStepRate = float(encoderMovementSteps) / float(ms - lastEncoderMovementMillis) * 1000.0;
 
                 if (encoderStepRate >= ENCODER_100X_STEPS_PER_SEC)     encoderMultiplier = 100;
                 else if (encoderStepRate >= ENCODER_10X_STEPS_PER_SEC) encoderMultiplier = 10;
               break;
           } // switch
         }
+
+      #if ENABLED(ADC_KEYPAD)
+        buttons_reprapworld_keypad = 0;
+      #endif
+
       #if ENABLED(ULTIPANEL)
         #define CURRENTSCREEN() (*currentScreen)(), lcd_clicked = false
       #else
         #if ENABLED(LCD_HAS_SLOW_BUTTONS)
           buttons |= slow_buttons;
         #endif
-        #if ENABLED(REPRAPWORLD_KEYPAD)
+
+        #if ENABLED(ADC_KEYPAD)
+
+          uint8_t newbutton_reprapworld_keypad = 0;
+          buttons = 0;
+          if (buttons_reprapworld_keypad == 0) {
+            newbutton_reprapworld_keypad = get_ADC_keyValue();
+            if (WITHIN(newbutton_reprapworld_keypad, 1, 8))
+              buttons_reprapworld_keypad = _BV(newbutton_reprapworld_keypad - 1);
+          }
+
+        #elif ENABLED(REPRAPWORLD_KEYPAD)
+
           GET_BUTTON_STATES(buttons_reprapworld_keypad);
+
         #endif
+
       #else
         GET_BUTTON_STATES(buttons);
       #endif // !NEWPANEL
 
 #endif // ULTIPANEL
 
+#if ENABLED(ADC_KEYPAD)
+
+  typedef struct {
+    uint16_t ADCKeyValueMin, ADCKeyValueMax;
+    uint8_t  ADCKeyNo;
+  } _stADCKeypadTable_;
+
+  static const _stADCKeypadTable_ stADCKeyTable[] = PROGMEM {
+    // VALUE_MIN, VALUE_MAX, KEY
+    { 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F1 + 1 },     // F1
+    { 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F2 + 1 },     // F2
+    { 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F3 + 1 },     // F3
+    {  300,  500, BLEN_REPRAPWORLD_KEYPAD_LEFT + 1 },   // LEFT
+    { 1900, 2200, BLEN_REPRAPWORLD_KEYPAD_RIGHT + 1 },  // RIGHT
+    {  570,  870, BLEN_REPRAPWORLD_KEYPAD_UP + 1 },     // UP
+    { 2670, 2870, BLEN_REPRAPWORLD_KEYPAD_DOWN + 1 },   // DOWN
+    { 1150, 1450, BLEN_REPRAPWORLD_KEYPAD_MIDDLE + 1 }, // ENTER
+  };
+
+  uint8_t get_ADC_keyValue(void) {
+    if (thermalManager.ADCKey_count >= 16) {
+      const uint16_t currentkpADCValue = thermalManager.current_ADCKey_raw >> 2;
+      #if ENABLED(ADC_KEYPAD_DEBUG)
+        SERIAL_PROTOCOLLN(currentkpADCValue);
+      #endif
+      thermalManager.current_ADCKey_raw = 0;
+      thermalManager.ADCKey_count = 0;
+      if (currentkpADCValue < 4000)
+        for (uint8_t i = 0; i < ADC_KEY_NUM; i++) {
+          const uint16_t lo = pgm_read_word(&stADCKeyTable[i].ADCKeyValueMin),
+                         hi = pgm_read_word(&stADCKeyTable[i].ADCKeyValueMax);
+          if (WITHIN(currentkpADCValue, lo, hi)) return pgm_read_byte(&stADCKeyTable[i].ADCKeyNo);
+        }
+    }
+    return 0;
+  }
+#endif
+
 #endif // ULTRA_LCD

Marlin/ultralcd.h

     void dontExpireStatus();
   #endif
 
+  #if ENABLED(ADC_KEYPAD)
+    uint8_t get_ADC_keyValue();
+  #endif
+
   #if ENABLED(DOGLCD)
     extern uint16_t lcd_contrast;
     void set_lcd_contrast(const uint16_t value);
     #define REPRAPWORLD_KEYPAD_MOVE_Y_UP    (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_UP)
     #define REPRAPWORLD_KEYPAD_MOVE_X_LEFT  (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_LEFT)
 
+    #if ENABLED(ADC_KEYPAD)
+      #define REPRAPWORLD_KEYPAD_MOVE_HOME  (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_F1)
+      #define KEYPAD_EN_C                   EN_REPRAPWORLD_KEYPAD_MIDDLE
+    #else
+      #define REPRAPWORLD_KEYPAD_MOVE_HOME  (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_MIDDLE)
+      #define KEYPAD_EN_C                   EN_REPRAPWORLD_KEYPAD_F1
+    #endif
+    #define REPRAPWORLD_KEYPAD_MOVE_MENU    (buttons_reprapworld_keypad & KEYPAD_EN_C)
+
+    #if BUTTON_EXISTS(ENC)
+      #define LCD_CLICKED ((buttons & EN_C) || REPRAPWORLD_KEYPAD_MOVE_MENU)
+    #else
+      #define LCD_CLICKED REPRAPWORLD_KEYPAD_MOVE_MENU
+    #endif
+
     #define REPRAPWORLD_KEYPAD_PRESSED      (buttons_reprapworld_keypad & ( \
                                               EN_REPRAPWORLD_KEYPAD_F3 | \
                                               EN_REPRAPWORLD_KEYPAD_F2 | \
                                               EN_REPRAPWORLD_KEYPAD_LEFT) \
                                             )
 
-    #define LCD_CLICKED ((buttons & EN_C) || (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_F1))
   #elif ENABLED(NEWPANEL)
     #define LCD_CLICKED (buttons & EN_C)
   #else

buildroot/bin/build_marlin

 #!/usr/bin/env bash
 
-arduino --verify --board arduino:avr:mega:cpu=atmega2560 Marlin/Marlin.ino
+case "$#" in
+  0 ) BOARD=arduino:avr:mega:cpu=atmega2560 ;;
+  * ) BOARD=arduino:avr:$1 ;;
+esac
+
+arduino --verify --board $BOARD Marlin/Marlin.ino

buildroot/bin/build_marlin_fail

 #!/usr/bin/env bash
 
-if arduino --verify --board arduino:avr:mega:cpu=atmega2560 Marlin/Marlin.ino ; then
-  return 1
-else
-  return 0
-fi
+build_marlin $@ && exit 0
+exit 1