Updates to Formbot T-Rex 2+ configuration files (#12422)

Updates to Formbot T-Rex 2+ configuration files

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h

 
 // For Cyclops or any "multi-extruder" that shares a single nozzle.
 //#define SINGLENOZZLE
+#if ENABLED(SINGLENOZZLE)
+  // Parameters for filament retract / prime on toolchange
+  #define SINGLENOZZLE_SWAP_LENGTH          12  // (mm)
+  #define SINGLENOZZLE_SWAP_RETRACT_SPEED 3600  // (mm/m)
+  #define SINGLENOZZLE_SWAP_PRIME_SPEED   3600  // (mm/m)
+  //#define SINGLENOZZLE_SWAP_PARK
+  #if ENABLED(SINGLENOZZLE_SWAP_PARK)
+    #define SINGLENOZZLE_TOOLCHANGE_XY    { X_MIN_POS + 10, Y_MIN_POS + 10 }
+    #define SINGLENOZZLE_PARK_XY_FEEDRATE 6000  // (mm/m)
+  #endif
+#endif
 
 /**
  * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
 // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
 // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
 // For the other hotends it is their distance from the extruder 0 hotend.
+//#define HOTEND_OFFSET_X {0.0, 20.00} // (mm) relative X-offset for each nozzle
+//#define HOTEND_OFFSET_Y {0.0, 5.00}  // (mm) relative Y-offset for each nozzle
+//#define HOTEND_OFFSET_Z {0.0, 0.00}  // (mm) relative Z-offset for each nozzle
 
 #ifdef ROXYs_TRex
   #define HOTEND_OFFSET_X {0.0, 0.00}  // (mm) for each extruder, offset of the hotend on the X axis
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  */
-//#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 160, 1600, 93 }
 #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 800, 93 }
 
 /**
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  */
-//#define DEFAULT_MAX_FEEDRATE          { 250, 150, 5, 25 }
 #define DEFAULT_MAX_FEEDRATE          { 250, 100, 5, 25 }
 
 /**
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-
-//#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
-//#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
-//#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
-
 #define DEFAULT_ACCELERATION          1500    // X, Y, Z and E acceleration for printing moves
 #define DEFAULT_RETRACT_ACCELERATION  1500    // E acceleration for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   1500    // X, Y, Z acceleration for travel (non printing) moves
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define DEFAULT_XJERK                 20.0
-//#define DEFAULT_YJERK                 10.0
-//#define DEFAULT_ZJERK                  0.4
-//#define DEFAULT_EJERK                  5.0
-
 #define DEFAULT_XJERK                 12.0   // More conservitive numbers.
 #define DEFAULT_YJERK                  8.0
 #define DEFAULT_ZJERK                  0.4
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
+
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
 #define MIN_PROBE_EDGE 0
 
 // X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 7000
+#define XY_PROBE_SPEED 5000
 
 // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
 #define Z_CLEARANCE_DEPLOY_PROBE    7 // Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES  7 // Z Clearance between probe points
 #define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
-#define Z_AFTER_PROBING             7 // Z position after probing is done
+#define Z_AFTER_PROBING            10 // Z position after probing is done
 
 #define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
 
 #define Z_MIN_POS 0
 #define X_MAX_POS 450
 #define Y_MAX_POS Y_BED_SIZE
-#if ENABLED(tallVersion)
-  #define Z_MAX_POS 700
-#else
-  #define Z_MAX_POS 500
-#endif
+#define Z_MAX_POS 700
+
+
+// Z raise distance for tool-change, as needed for some extruders
+#define TOOLCHANGE_ZRAISE     2  // (mm)
 
 /**
  * Software Endstops
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
-    #define MESH_TEST_HOTEND_TEMP  205.0  // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
+    #define MESH_TEST_HOTEND_TEMP  208.0  // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
     #define MESH_TEST_BED_TEMP      60.0  // (°C) Default bed temperature for the G26 Mesh Validation Tool.
   #endif
 
 //#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
-  #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
-  #define LCD_PROBE_Z_RANGE 4     // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
-  //#define MESH_EDIT_MENU        // Add a menu to edit mesh points
+  #define MBL_Z_STEP 0.025    // Step size while manually probing Z axis.
+  #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
+//#define MESH_EDIT_MENU        // Add a menu to edit mesh points
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
 #define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
-  #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2)    // X point for Z homing when homing all axes (G28).
-  #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2)    // Y point for Z homing when homing all axes (G28).
+  #define Z_SAFE_HOMING_X_POINT (((X_BED_SIZE) / 2) - 15)   // X point for Z homing when homing all axes (G28).
+  #define Z_SAFE_HOMING_Y_POINT (((Y_BED_SIZE) / 2) - 15)   // Y point for Z homing when homing all axes (G28).
 #endif
 
 // Homing speeds (mm/m)
 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS
 
+
 // @section calibrate
 
 /**
  *
  * View the current statistics with M78.
  */
-#define PRINTCOUNTER
+//#define PRINTCOUNTER
 
 //=============================================================================
 //============================= LCD and SD support ============================

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration_adv.h

  *
  * Define one or both of these to override the default 0-255 range.
  */
-#define FAN_MIN_PWM 64
+#define FAN_MIN_PWM 45
 //#define FAN_MAX_PWM 128
 
 // @section extruder
  */
 #define DUAL_X_CARRIAGE
 #if ENABLED(DUAL_X_CARRIAGE)
-  #define X1_MIN_POS X_MIN_POS  // set minimum to ensure first x-carriage doesn't hit the parked second X-carriage
-  #define X1_MAX_POS X_BED_SIZE // set maximum to ensure first x-carriage doesn't hit the parked second X-carriage
-  #define X2_MIN_POS  0     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
-  #define X2_MAX_POS (442-4.0) // set maximum to the distance between toolheads when both heads are homed
-  #define X2_HOME_DIR 1     // the second X-carriage always homes to the maximum endstop position
-  #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+  #define X1_MIN_POS X_MIN_POS        // set minimum to ensure first x-carriage doesn't hit the parked second X-carriage
+  #define X1_MAX_POS (X_BED_SIZE)     // set maximum to ensure first x-carriage doesn't hit the parked second X-carriage
+  #define X2_MIN_POS  0               // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+  #define X2_MAX_POS (442-4.0)        // set maximum to the distance between toolheads when both heads are homed
+  #define X2_HOME_DIR 1               // the second X-carriage always homes to the maximum endstop position
+  #define X2_HOME_POS X2_MAX_POS      // default home position is the maximum carriage position
       // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
       // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
       // without modifying the firmware (through the "M218 T1 X???" command).
   #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
 //#define MICROSTEP16 LOW,LOW,HIGH
 //#define MICROSTEP32 HIGH,LOW,HIGH
 
+
 // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
 #define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]
 
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
-#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
+#if HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)
     #define PROGRESS_BAR_BAR_TIME 2000    // (ms) Amount of time to show the bar
  *   'M106 P<fan> T2'     : Use the set secondary speed
  *   'M106 P<fan> T1'     : Restore the previous fan speed
  */
-#define EXTRA_FAN_SPEED
+//#define EXTRA_FAN_SPEED
 
 /**
  * Firmware-based and LCD-controlled retract
     //#define RETRACT_SYNC_MIXING         // Retract and restore all mixing steppers simultaneously
   #endif
 #endif
-
-/**
- * Universal tool change settings.
- * Applies to all types of extruders except where explicitly noted.
- */
-#if EXTRUDERS > 1
-  // Z raise distance for tool-change, as needed for some extruders
-  #define TOOLCHANGE_ZRAISE     2  // (mm)
-
-  // Retract and prime filament on tool-change
-  //#define TOOLCHANGE_FILAMENT_SWAP
-  #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
-    #define TOOLCHANGE_FIL_SWAP_LENGTH          12  // (mm)
-    #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600  // (mm/m)
-    #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED   3600  // (mm/m)
-  #endif
-
-  /**
-   * Position to park head during tool change.
-   * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER
-   */
-  //#define TOOLCHANGE_PARK
-  #if ENABLED(TOOLCHANGE_PARK)
-    #define TOOLCHANGE_PARK_XY    { X_MIN_POS + 10, Y_MIN_POS + 10 }
-    #define TOOLCHANGE_PARK_XY_FEEDRATE 6000  // (mm/m)
-  #endif
-#endif
-
 /**
  * Advanced Pause
  * Experimental feature for filament change support and for parking the nozzle when paused.
                                                   //   until extrusion is consistent, and to purge old filament.
 
                                                   // Filament Unload does a Retract, Delay, and Purge first:
-  #define FILAMENT_UNLOAD_RETRACT_LENGTH       4  // (mm) Unload initial retract length.
-  #define FILAMENT_UNLOAD_DELAY             5000  // (ms) Delay for the filament to cool after retract.
+  #define FILAMENT_UNLOAD_RETRACT_LENGTH       0  // (mm) Unload initial retract length.
+  #define FILAMENT_UNLOAD_DELAY              500  // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH         0  // (mm) An unretract is done, then this length is purged.
 
-  #define PAUSE_PARK_NOZZLE_TIMEOUT           45  // (seconds) Time limit before the nozzle is turned off for safety.
-  #define FILAMENT_CHANGE_ALERT_BEEPS          1  // Number of alert beeps to play when a response is needed.
+  #define PAUSE_PARK_NOZZLE_TIMEOUT       (3*60)  // (seconds) Time limit before the nozzle is turned off for safety.
+  #define FILAMENT_CHANGE_ALERT_BEEPS          3  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
   #define PARK_HEAD_ON_PAUSE                      // Park the nozzle during pause and filament change.
   #define HOME_BEFORE_FILAMENT_CHANGE             // Ensure homing has been completed prior to parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
-  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+  #define FILAMENT_LOAD_UNLOAD_GCODES             // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_UNLOAD_ALL_EXTRUDERS           // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
 #endif
 
 /**
- * G-code Macros
- *
- * Add G-codes M810-M819 to define and run G-code macros.
- * Macros are not saved to EEPROM.
- */
-//#define GCODE_MACROS
-#if ENABLED(GCODE_MACROS)
-  #define GCODE_MACROS_SLOTS       5  // Up to 10 may be used
-  #define GCODE_MACROS_SLOT_SIZE  50  // Maximum length of a single macro
-#endif
-
-/**
  * User-defined menu items that execute custom GCode
  */
 //#define CUSTOM_USER_MENUS
 
   #define MAX7219_GCODE            // Add the M7219 G-code to control the LED matrix
   #define MAX7219_INIT_TEST    2   // Do a test pattern at initialization (Set to 2 for spiral)
-  #define MAX7219_NUMBER_UNITS 2   // Number of Max7219 units in chain.
+  #define MAX7219_NUMBER_UNITS 3   // Number of Max7219 units in chain.
   #define MAX7219_ROTATE       0   // Rotate the display clockwise (in multiples of +/- 90°)
                                    // connector at:  right=0   bottom=-90  top=90  left=180
   #define MAX7219_REVERSE_ORDER   // The individual LED matrix units may be in reversed order

Marlin/src/config/examples/Formbot/T_Rex_2+/_Bootscreen.h

 
 #define CUSTOM_BOOTSCREEN_TIMEOUT   2500
 #define CUSTOM_BOOTSCREEN_BMPWIDTH  128
+#define CUSTOM_BOOTSCREEN_BMPHEIGHT 64
 
 const unsigned char custom_start_bmp[] PROGMEM = {
   B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,