SKR Pro 1.1 WiFi and LCD SD card support (#17531)

Marlin/src/HAL/shared/esp_wifi.cpp

+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include "../../inc/MarlinConfig.h"
+#include "Delay.h"
+
+void esp_wifi_init(void) {
+  #if PIN_EXISTS(ESP_WIFI_MODULE_RESET)
+    OUT_WRITE(ESP_WIFI_MODULE_RESET_PIN, LOW);
+    delay(1);
+    OUT_WRITE(ESP_WIFI_MODULE_RESET_PIN, HIGH);
+  #endif
+  #if PIN_EXISTS(ESP_WIFI_MODULE_ENABLE)
+    OUT_WRITE(ESP_WIFI_MODULE_ENABLE_PIN, HIGH);
+  #endif
+}

Marlin/src/HAL/shared/esp_wifi.h

+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+void esp_wifi_init();

Marlin/src/MarlinCore.cpp

 #include "feature/closedloop.h"
 
 #include "HAL/shared/Delay.h"
+#include "HAL/shared/esp_wifi.h"
 
 #include "module/stepper/indirection.h"
 
     BOARD_INIT();
   #endif
 
+  SETUP_RUN(esp_wifi_init());
+
   // Check startup - does nothing if bootloader sets MCUSR to 0
   byte mcu = HAL_get_reset_source();
   if (mcu &  1) SERIAL_ECHOLNPGM(STR_POWERUP);

Marlin/src/pins/pinsDebug_list.h

 #if PIN_EXISTS(CLOSED_LOOP_MOVE_COMPLETE)
   REPORT_NAME_DIGITAL(__LINE__, CLOSED_LOOP_MOVE_COMPLETE_PIN)
 #endif
+#if PIN_EXISTS(ESP_WIFI_MODULE_RESET)
+  REPORT_NAME_DIGITAL(__LINE__, ESP_WIFI_MODULE_RESET_PIN)
+#endif
+#if PIN_EXISTS(ESP_WIFI_MODULE_ENABLE)
+  REPORT_NAME_DIGITAL(__LINE__, ESP_WIFI_MODULE_ENABLE_PIN)
+#endif

Marlin/src/pins/stm32f4/pins_BLACK_STM32F407VE.h

 #define SDIO_CK_PIN                         PC12
 #define SDIO_CMD_PIN                        PD2
 
-#if !defined(SDCARD_CONNECTION) || SD_CONNECTION_IS(ONBOARD)
+#ifndef SDCARD_CONNECTION
+  #define SDCARD_CONNECTION              ONBOARD
+#endif
+
+#if SD_CONNECTION_IS(ONBOARD)
   #define SDIO_SUPPORT                            // Use SDIO for onboard SD
 
   #ifndef SDIO_SUPPORT

Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_V1_1.h

 
 // Use one of these or SDCard-based Emulation will be used
 //#define SRAM_EEPROM_EMULATION                   // Use BackSRAM-based EEPROM emulation
-//#define FLASH_EEPROM_EMULATION                  // Use Flash-based EEPROM emulation
+#define FLASH_EEPROM_EMULATION                    // Use Flash-based EEPROM emulation
 
 //
 // Servos
 #define HEATER_BED_PIN                      PD12  // Hotbed
 #define FAN_PIN                             PC8   // Fan0
 #define FAN1_PIN                            PE5   // Fan1
-#define FAN2_PIN                            PE6   // Fan2
+#define FAN2_PIN                            PE6
+
+#ifndef E0_AUTO_FAN_PIN
+  #define E0_AUTO_FAN_PIN                   PC9
+#endif
 
 //
 // Misc. Functions
 
 //
 // Onboard SD card
-//   NOT compatible with LCD
+// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
 //
-#if SDCARD_CONNECTION == ONBOARD && !HAS_SPI_LCD
+#if SD_CONNECTION_IS(ONBOARD)
   #define SOFTWARE_SPI                            // Use soft SPI for onboard SD
   #define SDSS                              PA4
   #define SCK_PIN                           PA5
   #define MISO_PIN                          PA6
   #define MOSI_PIN                          PB5
-#else
-  #define SDSS                              PB12
 #endif
 
 /**
 #if HAS_SPI_LCD
   #define BEEPER_PIN                        PG4
   #define BTN_ENC                           PA8
+  #if SD_CONNECTION_IS(LCD)
+    #define SDSS                            PB12  // Uses default hardware SPI for LCD's SD
+  #endif
 
   #if ENABLED(CR10_STOCKDISPLAY)
     #define LCD_PINS_RS                     PG6
     #undef ST7920_DELAY_2
     #undef ST7920_DELAY_3
 
+  #elif ENABLED(MKS_MINI_12864)
+    #define DOGLCD_A0                       PG6
+    #define DOGLCD_CS                       PG3
+
   #else
 
     #define LCD_PINS_RS                     PD10
   #endif
 
 #endif // HAS_SPI_LCD
+
+//
+// WIFI
+//
+
+/**
+ *          _____
+ *      TX | 1 2 | GND      Enable PG1   // Must be high for module to run
+ *  Enable | 3 4 | GPIO2    Reset  PG0   // Leave as unused (OK to leave floating)
+ *   Reset | 5 6 | GPIO0    GPIO2  PF15  // Leave as unused (best to leave floating)
+ *     3.3V| 7 8 | RX       GPIO0  PF14  // Leave as unused (best to leave floating)
+ *           ￣￣
+ *            W1
+ */
+#define ESP_WIFI_MODULE_COM 6                     // must also set SERIAL_PORT or SERIAL_PORT_2 to this
+#define ESP_WIFI_MODULE_BAUDRATE        BAUDRATE  //115200   // use BAUDRATE ?  would guarantee same baud rate as SERIAL_PORT & SERIAL_PORT_2
+#define ESP_WIFI_MODULE_RESET_PIN           -1
+#define ESP_WIFI_MODULE_ENABLE_PIN          PG1

Marlin/src/pins/stm32f4/pins_FLYF407ZG.h

 #define SDIO_CK_PIN                         PC12
 #define SDIO_CMD_PIN                        PD2
 
-#if !defined(SDCARD_CONNECTION) || SD_CONNECTION_IS(ONBOARD)
+#ifndef SDCARD_CONNECTION
+  #define SDCARD_CONNECTION              ONBOARD
+#endif
+
+#if SD_CONNECTION_IS(ONBOARD)
   #define SDIO_SUPPORT                            // Use SDIO for onboard SD
 
   #ifndef SDIO_SUPPORT