Updated documentation in Configuration.h.
Cleaned up and commented some code relating to Z_PROBE_ENDSTOP.
Separated Z_MIN_ENDSTOP and Z_PROBE_ENDSTOP completely.

- Include the current Z when raising the axis after and between probing
- Add `sync_plan_position_delta` for parity with `sync_plan_position`
- Clean up and clarify `M48`, `dock_sled`, and others

* Added MSG_END_HOUR and MSG_END_MINUTE labels to all language files.
* Available translations:
  EN, FR, DE, ES, IT, PT, PT-BR.

The current position needs to be updated by using the inverse
`plan_bed_level_matrix` on X, Y, and Z. All moves in the planner are
transformed by the `plan_bed_level_matrix` from this point forward.

Code to raise the probe before retraction is good, but the code should
always raise the probe, not just when retracting

- Addressing issue #1741

Documented some additional areas that should be addressed if Z_PROBE is
fully separated from Z_MIN or Z_MAX.
Fixed a documentation error in sanity checks. Servos start at 0 not 1.

This rolls back to commit 06f767d608.

- Some messages should not expire with `PROGRESS_MSG_EXPIRE`.
- Simplify conditional for progress bar with sanity checks.
- Rename `messageTick` to `expireStatusMillis` and make it the expire
time.

Fix for #1460.

Seems to work with only one extruder. Can't test this myself with more.

A `z_before` value is passed to probe_pt, but the `retract_z_probe`
function assumes that Z is 0, doesn’t add `current_position[Z_AXIS]` as
other cases do. This may be superfluous, so this is a test, and will be
reverted if it has no effect.

- Fix `prepare_move` function not calling `adjust_delta`
- Add more shorthand for plan_buffer_line.
- Fix wrong `federate` usage, assuming they are all mm/m
- Minor `stepper.cpp` cleanup

- Users prefer `G29 E` to work like `M48 E` so fixed that
- `M48 n` replaced with `M48 P` (or `p`). `n` legacy support
- Shorten some strings to save precious bytes
- Smaller code for 3-point probing

- Fixed a typo causing G28 to home incorrectly
- Added documentation to G28
- Added homeXYZ bools to neaten the code
- Added a note about home_offsets being questionable

unless Z_SAFE_HOMING is.

Code cleanup for Z_PROBE_AND_ENDSTOP.
Added Z_PROBE_PIN to pins_RAMPS_13.h

- Add some documentation to planner and stepper headers
- Patch up RAMBO pins with undefs
- Add `sync_plan_position` inline to set current XYZE
- Swap indices in `extruder_offset` to fix initialization values

be.
Added Sanity Check for it.
Added hook so it's enabled.

- Patched up for most included configurations

- Also patch up some warnings

- Fix a bug reading `code_value` for `M503 Sn`
- Hide and remove unused variables

- Also a small tweak to SanityCheck.h

to avoid:
Marlin_main.cpp:1790: warning: array subscript is above array bounds.

- Init `zprobe_zoffset`
- Remove `current_position[Z_AXIS] = zprobe_zoffset` lines from the
`set_bed_level_equation_*` functions
- Apply standards to `mesh_bed_leveling` files
- Document `MESH_BED_LEVELING`

if not have SDSUPPORT the fromsd array is not necessary

It just probe all the bed without appliying the matrix.
Useful after a first G29 to check the topology.

ZigZag: Inverted Behavior.. If T supplied, it does not zigzag.
Topograph table: The table was rotated 90º clockwise.

Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z
steppers - Let's call them Z stepper and Z2 stepper.
That way the machine is capable to align the bed during home, since both
Z steppers are homed.
There is also an implementation of M666 (software endstops adjustment)
to this feature.
After Z homing, this adjustment is applied to just one of the steppers
in order to align the bed.
One just need to home the Z axis and measure the distance difference
between both Z axis and apply the math: Z adjust = Z - Z2.
If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it
is.. think about it) and the Z adjust would be positive.
Play a little bit with small adjustments (0.5mm) and check the
behaviour.
The M119 (endstops report) will start reporting the Z2 Endstop as well.

- Address issue #1669
- Remove the TOPO_ORIGIN configuration setting