Allow `ENABLED`, `DISABLED`, `PIN_EXISTS`, and `BUTTON_EXISTS` to take multiple arguments. Also add:
- Alias `ANY(...)` for `!DISABLED(...)`
- Alias `ANY_PIN(...)` for `PIN_EXISTS(a) || PIN_EXISTS(b) ...`
- Alias `EITHER(A,B)` for `ANY(...)`
- Alias `ALL(...)` and `BOTH(A,B)` for `ENABLED(...)`
- `NONE(...)` for `DISABLED(...)`

Co-Authored-By: ejtagle <ejtagle@hotmail.com>

* Fix some 8-bit Teensyduino compile warnings

-Override Teensyduino legacy NOT_A_PIN 127 define
-some fixups for Printrboard_RevF pins

* Proper cleanup of Printrboard Rev.F pins

* Apply LCD fixes to Printrboard v1

-Update Arduino IDE extension descriptions
-Set default motor currents if not defined in Configuration_adv.h
-Support for MINIPANEL LCD
-Support for choosing internal or panel SD

・More ANALOG NUMBERING to Analog Input
・Add comment header to all the section of all the pins files

・Sort sections as follows:
1. Some special definitions (USBCON, LARGE_FLASH, etc)
2. Servos
3. Limit Switches
4. Z Probe
5. Steppers
6. Temperature Sensors
7. Heaters / Fans
8. Misc. Functions
9. LCD / Controller

・Move MAX6675_SS into "Temperature Sensors" section
・Adjust spacing

Replace all fastDigitalRead/Write() with READ/WRITE()

Define SCK_PIN, MISO_PIN, MOSI_PIN in pins.h if not already defined in the pins_*.h files.

Remove these conditional pin definitions from the pin-files. They are now always defined.

Define separate sets of SPI-pins for AT90USB with and without Teensy support in fastio.h.
Likely this was the main reason for all that confusion about the AT90USB-SPI pins.

Includes:
  *firmware version / branch / date.
  *extruder count
  *board information (name, serial details, power supply type)
  *thermistors (names, min/max temperatures)
  *printer statistics (PRINTCOUNTER details)

Thanks to @thinkyhead for contributions.

Following up on #3231

The PrintrBoard Rev F utilizes a mcp4728 DAC to set motor current. Printrbot's implementation utilizes 2 new M-codes to set and write the DAC settings to the DAC EEPROM: `M909` (Read DAC) and `M910` (Write DAC). `M907` is re-used to set value, `M908` for direct control.

The Pins file for the RevF board is included.

Based on #2860 - rebased for RCBugFix

Remove unused ALARM_PIN from all the Configuration.h's

Keep "astyled" reformatting

- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`

- Rename the pin so it can be tested with `PIN_EXISTS`
- Fix some incorrect tests for `SDCARDDETECT`

For consistency with other pins, allowing use of `PIN_EXISTS` macro.

Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.

I added in the pins into the new board files for the Azteeg X3, X3 Pro,
Printrboard, and Rambo. I'm sure it can be added for others too but
these are the manual specified pins. Just like many things here though,
I can't test for the boards other than the Azteeg X3 Pro. Hopefully it
works smoothly for everyone who happens on this nifty display. :)

Hopefully this is helpful to organization and future expansion….

Hopefully this is helpful to organization and future expansion….

Hopefully this is helpful to organization and future expansion….