marlin

提交图

作者	SHA1	备注	提交日期
Scott Lahteine	c87b0e21be	Add units to probe speed comments	7 年前
Scott Lahteine	05c33833e7	[2.0.x] Add NO_LCD_MENUS option (#10582)	7 年前
Scott Lahteine	ed8d2bc225	Clean up some endstop inverting examples	7 年前
Scott Lahteine	9e07df5c1b	Extra options for LEVEL_BED_CORNERS (#10483)	7 年前
Scott Lahteine	a90cbc6339	[2.0.x] Wait for bed heaters between probing (#10472)	7 年前
KangDroid	6c535081ec	[2.0.x] Add optional menu item to toggle software endstops (#10389)	7 年前
Yunhui Fu	c96412a78f	[2.0.x] UTF-8 language translation support (#10213)	7 年前
Scott Lahteine	82dafbba33	Add Z_PROBE_LOW_POINT to example configs	7 年前
Scott Lahteine	dca69efc11	Update Bed PID comments	7 年前
Scott Lahteine	5932df7ea1	Add BEZIER_JERK_CONTROL to example configs	7 年前
Scott Lahteine	5b3bda1c16	Add Chamber Temp options to example configs	7 年前
Scott Lahteine	adcb87f0db	Z Endstop Servo => Z Probe Servo	7 年前
Scott Lahteine	dd2949922b	Consolidate 3-point leveling point options	7 年前
Scott Lahteine	c6ff39cc14	Spacing cleanup	7 年前
Scott Lahteine	14c03cb6f4	[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) (#10069) Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.	7 年前
Scott Lahteine	28f1276286	[2.0.x] Add Z_AFTER_PROBING option (#10058) Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.	7 年前
Scott Lahteine	79e6d890d5	Add UNKNOWN_Z_NO_RAISE to example configs	7 年前
Scott Lahteine	a2a672449a	Updated boot screen description	7 年前
Scott Lahteine	4953fb1c88	Standardize encoder defaults	7 年前
Scott Lahteine	5684beae90	Bring some configs up to speed	7 年前
Scott Lahteine	2024775e07	Spanish (UTF8) Language (#9786) From #7314 by @MrAmericanMike	7 年前
Scott Lahteine	17d984eab3	Add RESTORE_LEVELING_AFTER_G28 to example configs	7 年前
Scott Lahteine	7d8c6b3f3c	Add 20x4 option for Sainsmart LCD (#9740)	7 年前
Marcio Teixeira	aada1e698f	Removed unused configuration options.	7 年前
Scott Lahteine	8733d5a296	Add NUM_RUNOUT_SENSORS to example configs	7 年前
Scott Lahteine	ca55f2927a	Pulldown pin mode support (#9701) Implemented for LPC1768.	7 年前
Scott Lahteine	79272f98fc	Proposed changes to ST7920 lightweight status screen	7 年前
Marcio Teixeira	24eb275b99	Added a light-weight status screen for the ST7920 - The status screen uses the ST7920 character generator to greatly reduce SPI traffic and MCU load when updating the status screen. - Has been tested with the RepRapDiscount Full Graphics Smart Controller but should work with any LCD that uses an ST7920 or fully compatible controller.	7 年前
Roxy-3D	21e60fd3ed	Allow user to control Z-Height correction for off mesh movements (#9661)	7 年前
Marcio Teixeira	4880ac6533	Added a light-weight status screen for the ST7920 - The status screen uses the ST7920 character generator to greatly reduce SPI traffic and MCU load when updating the status screen. - Has been tested with the RepRapDiscount Full Graphics Smart Controller but should work with any LCD that uses an ST7920 or fully compatible controller.	7 年前
Scott Lahteine	2ec65051fd	Fix serial comment sp.	7 年前
Scott Lahteine	38c7d53bf7	Repair some spacing	7 年前
Scott Lahteine	2014d38e10	NEOPIXEL_BRIGHTNESS parity	7 年前
Scott Lahteine	b5e92f4f90	[2.0.x] Enable / disable PSU automatically (#9503)	7 年前
Scott Lahteine	eecb0188c0	Add ULTI_CONTROLLER to example configs	7 年前
Scott Lahteine	4925f60cff	Add MALYAN_LCD to configs	7 年前
Scott Lahteine	7d6c009104	Add thermistor 15 tuned for JGAurora A5	7 年前
Scott Lahteine	348b454401	Probe bounds based on bed size	7 年前
Scott Lahteine	58ed9901d7	Consistent NEOPIXEL_TYPE options	7 年前
Scott Lahteine	fa432508b0	Followup to Ender config	7 年前
Thomas Moore	dabb75034c	Update example configurations	7 年前
GMagician	5295b4713d	[2.0.x] add semitec 104NT-4 (#9119) Table is very very similar to old 104-GT2 so I added only the name and recycled old ID	7 年前
Thomas Moore	f0a8a1a853	[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE (#8866) * Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE	7 年前
Scott Lahteine	1cf1cf8759	Add RADDS_DISPLAY to example configs	7 年前
Scott Lahteine	f79026acc1	Apply MKS_12864OLED_SSD1306 to examples Followup to #8814	7 年前
Scott Lahteine	9abbcc3ee0	Apply ZONESTAR_LCD to example configs	7 年前
Scott Lahteine	69d49a2438	Shorter segments may be better	7 年前
Scott Lahteine	d7800e7975	Apply MULTIPLE_PROBING to example configs	7 年前
Richard Wackerbarth	c1184552ac	Change K1 to required option PID_K1	7 年前
Scott Lahteine	aa7efb96bf	Bring configurations up to date	7 年前

56 次代码提交 (c87b0e21beb516ed1aa783657fbdc93ee4f14057)