My Marlin configs for Fabrikator Mini and CTC i3 Pro B
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

Configuration.h 57KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644645646647648649650651652653654655656657658659660661662663664665666667668669670671672673674675676677678679680681682683684685686687688689690691692693694695696697698699700701702703704705706707708709710711712713714715716717718719720721722723724725726727728729730731732733734735736737738739740741742743744745746747748749750751752753754755756757758759760761762763764765766767768769770771772773774775776777778779780781782783784785786787788789790791792793794795796797798799800801802803804805806807808809810811812813814815816817818819820821822823824825826827828829830831832833834835836837838839840841842843844845846847848849850851852853854855856857858859860861862863864865866867868869870871872873874875876877878879880881882883884885886887888889890891892893894895896897898899900901902903904905906907908909910911912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944945946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983984985986987988989990991992993994995996997998999100010011002100310041005100610071008100910101011101210131014101510161017101810191020102110221023102410251026102710281029103010311032103310341035103610371038103910401041104210431044104510461047104810491050105110521053105410551056105710581059106010611062106310641065106610671068106910701071107210731074107510761077107810791080108110821083108410851086108710881089109010911092109310941095109610971098109911001101110211031104110511061107110811091110111111121113111411151116111711181119112011211122112311241125112611271128112911301131113211331134113511361137113811391140114111421143114411451146114711481149115011511152115311541155115611571158115911601161116211631164116511661167116811691170117111721173117411751176117711781179118011811182118311841185118611871188118911901191119211931194119511961197119811991200120112021203120412051206120712081209121012111212121312141215121612171218121912201221122212231224122512261227122812291230123112321233123412351236123712381239124012411242124312441245124612471248124912501251125212531254125512561257125812591260126112621263126412651266126712681269127012711272127312741275127612771278127912801281128212831284128512861287128812891290129112921293129412951296129712981299130013011302130313041305130613071308130913101311131213131314131513161317131813191320132113221323132413251326132713281329133013311332133313341335133613371338133913401341134213431344134513461347134813491350135113521353135413551356135713581359136013611362136313641365136613671368136913701371137213731374137513761377137813791380138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410141114121413141414151416141714181419142014211422142314241425142614271428142914301431143214331434143514361437143814391440144114421443144414451446144714481449145014511452145314541455145614571458145914601461146214631464146514661467146814691470147114721473147414751476147714781479148014811482148314841485148614871488148914901491149214931494149514961497
  1. /**
  2. * Marlin 3D Printer Firmware
  3. * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4. *
  5. * Based on Sprinter and grbl.
  6. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7. *
  8. * This program is free software: you can redistribute it and/or modify
  9. * it under the terms of the GNU General Public License as published by
  10. * the Free Software Foundation, either version 3 of the License, or
  11. * (at your option) any later version.
  12. *
  13. * This program is distributed in the hope that it will be useful,
  14. * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15. * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  16. * GNU General Public License for more details.
  17. *
  18. * You should have received a copy of the GNU General Public License
  19. * along with this program. If not, see <http://www.gnu.org/licenses/>.
  20. *
  21. */
  22. /**
  23. * Configuration.h
  24. *
  25. * Basic settings such as:
  26. *
  27. * - Type of electronics
  28. * - Type of temperature sensor
  29. * - Printer geometry
  30. * - Endstop configuration
  31. * - LCD controller
  32. * - Extra features
  33. *
  34. * Advanced settings can be found in Configuration_adv.h
  35. *
  36. */
  37. #ifndef CONFIGURATION_H
  38. #define CONFIGURATION_H
  39. /**
  40. *
  41. * ***********************************
  42. * ** ATTENTION TO ALL DEVELOPERS **
  43. * ***********************************
  44. *
  45. * You must increment this version number for every significant change such as,
  46. * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
  47. *
  48. * Note: Update also Version.h !
  49. */
  50. #define CONFIGURATION_H_VERSION 010100
  51. //===========================================================================
  52. //============================= Getting Started =============================
  53. //===========================================================================
  54. /**
  55. * Here are some standard links for getting your machine calibrated:
  56. *
  57. * http://reprap.org/wiki/Calibration
  58. * http://youtu.be/wAL9d7FgInk
  59. * http://calculator.josefprusa.cz
  60. * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  61. * http://www.thingiverse.com/thing:5573
  62. * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  63. * http://www.thingiverse.com/thing:298812
  64. */
  65. //===========================================================================
  66. //============================= DELTA Printer ===============================
  67. //===========================================================================
  68. // For a Delta printer replace the configuration files with the files in the
  69. // example_configurations/delta directory.
  70. //
  71. //===========================================================================
  72. //============================= SCARA Printer ===============================
  73. //===========================================================================
  74. // For a Scara printer replace the configuration files with the files in the
  75. // example_configurations/SCARA directory.
  76. //
  77. // @section info
  78. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  79. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  80. // build by the user have been successfully uploaded into firmware.
  81. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  82. #define SHOW_BOOTSCREEN
  83. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  84. #define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
  85. //
  86. // *** VENDORS PLEASE READ *****************************************************
  87. //
  88. // Marlin now allow you to have a vendor boot image to be displayed on machine
  89. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  90. // custom boot image and then the default Marlin boot image is shown.
  91. //
  92. // We suggest for you to take advantage of this new feature and keep the Marlin
  93. // boot image unmodified. For an example have a look at the bq Hephestos 2
  94. // example configuration folder.
  95. //
  96. //#define SHOW_CUSTOM_BOOTSCREEN
  97. // @section machine
  98. /**
  99. * Select which serial port on the board will be used for communication with the host.
  100. * This allows the connection of wireless adapters (for instance) to non-default port pins.
  101. * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  102. *
  103. * :[0, 1, 2, 3, 4, 5, 6, 7]
  104. */
  105. #define SERIAL_PORT 0
  106. /**
  107. * This setting determines the communication speed of the printer.
  108. *
  109. * 250000 works in most cases, but you might try a lower speed if
  110. * you commonly experience drop-outs during host printing.
  111. *
  112. * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
  113. */
  114. #define BAUDRATE 250000
  115. // Enable the Bluetooth serial interface on AT90USB devices
  116. //#define BLUETOOTH
  117. // The following define selects which electronics board you have.
  118. // Please choose the name from boards.h that matches your setup
  119. #ifndef MOTHERBOARD
  120. #define MOTHERBOARD BOARD_OMCA
  121. #endif
  122. // Optional custom name for your RepStrap or other custom machine
  123. // Displayed in the LCD "Ready" message
  124. //#define CUSTOM_MACHINE_NAME "3D Printer"
  125. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  126. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  127. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  128. // This defines the number of extruders
  129. // :[1, 2, 3, 4]
  130. #define EXTRUDERS 1
  131. // Enable if your E steppers or extruder gear ratios are not identical
  132. //#define DISTINCT_E_FACTORS
  133. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  134. //#define SINGLENOZZLE
  135. // A dual extruder that uses a single stepper motor
  136. // Don't forget to set SSDE_SERVO_ANGLES and HOTEND_OFFSET_X/Y/Z
  137. //#define SWITCHING_EXTRUDER
  138. #if ENABLED(SWITCHING_EXTRUDER)
  139. #define SWITCHING_EXTRUDER_SERVO_NR 0
  140. #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
  141. //#define HOTEND_OFFSET_Z {0.0, 0.0}
  142. #endif
  143. /**
  144. * "Mixing Extruder"
  145. * - Adds a new code, M165, to set the current mix factors.
  146. * - Extends the stepping routines to move multiple steppers in proportion to the mix.
  147. * - Optional support for Repetier Host M163, M164, and virtual extruder.
  148. * - This implementation supports only a single extruder.
  149. * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  150. */
  151. //#define MIXING_EXTRUDER
  152. #if ENABLED(MIXING_EXTRUDER)
  153. #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
  154. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
  155. //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
  156. #endif
  157. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  158. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  159. // For the other hotends it is their distance from the extruder 0 hotend.
  160. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  161. //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  162. /**
  163. * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  164. *
  165. * 0 = No Power Switch
  166. * 1 = ATX
  167. * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  168. *
  169. * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  170. */
  171. #define POWER_SUPPLY 1
  172. #if POWER_SUPPLY > 0
  173. // Enable this option to leave the PSU off at startup.
  174. // Power to steppers and heaters will need to be turned on with M80.
  175. //#define PS_DEFAULT_OFF
  176. #endif
  177. // @section temperature
  178. //===========================================================================
  179. //============================= Thermal Settings ============================
  180. //===========================================================================
  181. /**
  182. * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  183. *
  184. * Temperature sensors available:
  185. *
  186. * -3 : thermocouple with MAX31855 (only for sensor 0)
  187. * -2 : thermocouple with MAX6675 (only for sensor 0)
  188. * -1 : thermocouple with AD595
  189. * 0 : not used
  190. * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  191. * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  192. * 3 : Mendel-parts thermistor (4.7k pullup)
  193. * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  194. * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  195. * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  196. * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  197. * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  198. * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  199. * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  200. * 10 : 100k RS thermistor 198-961 (4.7k pullup)
  201. * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
  202. * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  203. * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  204. * 20 : the PT100 circuit found in the Ultimainboard V2.x
  205. * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  206. * 66 : 4.7M High Temperature thermistor from Dyze Design
  207. * 70 : the 100K thermistor found in the bq Hephestos 2
  208. * 75 : 100k Generic Silicon Heat Pad typically a NTC 100K MGB18-104F39050L32 thermistor
  209. *
  210. * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  211. * (but gives greater accuracy and more stable PID)
  212. * 51 : 100k thermistor - EPCOS (1k pullup)
  213. * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  214. * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  215. *
  216. * 1047 : Pt1000 with 4k7 pullup
  217. * 1010 : Pt1000 with 1k pullup (non standard)
  218. * 147 : Pt100 with 4k7 pullup
  219. * 110 : Pt100 with 1k pullup (non standard)
  220. *
  221. * Use these for Testing or Development purposes. NEVER for production machine.
  222. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  223. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  224. *
  225. * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  226. */
  227. #define TEMP_SENSOR_0 5
  228. #define TEMP_SENSOR_1 0
  229. #define TEMP_SENSOR_2 0
  230. #define TEMP_SENSOR_3 0
  231. #define TEMP_SENSOR_BED 5
  232. // Dummy thermistor constant temperature readings, for use with 998 and 999
  233. #define DUMMY_THERMISTOR_998_VALUE 25
  234. #define DUMMY_THERMISTOR_999_VALUE 100
  235. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  236. // from the two sensors differ too much the print will be aborted.
  237. //#define TEMP_SENSOR_1_AS_REDUNDANT
  238. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  239. // Extruder temperature must be close to target for this long before M109 returns success
  240. #define TEMP_RESIDENCY_TIME 10 // (seconds)
  241. #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  242. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  243. // Bed temperature must be close to target for this long before M190 returns success
  244. #define TEMP_BED_RESIDENCY_TIME 0 // (seconds)
  245. #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
  246. #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  247. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  248. // to check that the wiring to the thermistor is not broken.
  249. // Otherwise this would lead to the heater being powered on all the time.
  250. #define HEATER_0_MINTEMP 5
  251. #define HEATER_1_MINTEMP 5
  252. #define HEATER_2_MINTEMP 5
  253. #define HEATER_3_MINTEMP 5
  254. #define BED_MINTEMP 5
  255. // When temperature exceeds max temp, your heater will be switched off.
  256. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  257. // You should use MINTEMP for thermistor short/failure protection.
  258. #define HEATER_0_MAXTEMP 275
  259. #define HEATER_1_MAXTEMP 275
  260. #define HEATER_2_MAXTEMP 275
  261. #define HEATER_3_MAXTEMP 275
  262. #define BED_MAXTEMP 150
  263. //===========================================================================
  264. //============================= PID Settings ================================
  265. //===========================================================================
  266. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  267. // Comment the following line to disable PID and enable bang-bang.
  268. #define PIDTEMP
  269. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  270. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  271. #if ENABLED(PIDTEMP)
  272. //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  273. //#define PID_DEBUG // Sends debug data to the serial port.
  274. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  275. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  276. //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  277. // Set/get with gcode: M301 E[extruder number, 0-2]
  278. #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  279. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  280. #define K1 0.95 //smoothing factor within the PID
  281. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  282. // J-Head Mk V-B
  283. #define DEFAULT_Kp 25.05
  284. #define DEFAULT_Ki 2.30
  285. #define DEFAULT_Kd 68.15
  286. #endif // PIDTEMP
  287. //===========================================================================
  288. //============================= PID > Bed Temperature Control ===============
  289. //===========================================================================
  290. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  291. //
  292. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  293. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  294. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  295. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  296. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  297. // shouldn't use bed PID until someone else verifies your hardware works.
  298. // If this is enabled, find your own PID constants below.
  299. //#define PIDTEMPBED
  300. //#define BED_LIMIT_SWITCHING
  301. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  302. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  303. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  304. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  305. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  306. #if ENABLED(PIDTEMPBED)
  307. //#define PID_BED_DEBUG // Sends debug data to the serial port.
  308. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  309. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  310. #define DEFAULT_bedKp 10.00
  311. #define DEFAULT_bedKi .023
  312. #define DEFAULT_bedKd 305.4
  313. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  314. //from pidautotune
  315. //#define DEFAULT_bedKp 97.1
  316. //#define DEFAULT_bedKi 1.41
  317. //#define DEFAULT_bedKd 1675.16
  318. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  319. #endif // PIDTEMPBED
  320. // @section extruder
  321. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  322. // It also enables the M302 command to set the minimum extrusion temperature
  323. // or to allow moving the extruder regardless of the hotend temperature.
  324. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  325. #define PREVENT_COLD_EXTRUSION
  326. #define EXTRUDE_MINTEMP 170
  327. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  328. // Note that for Bowden Extruders a too-small value here may prevent loading.
  329. #define PREVENT_LENGTHY_EXTRUDE
  330. #define EXTRUDE_MAXLENGTH 200
  331. //===========================================================================
  332. //======================== Thermal Runaway Protection =======================
  333. //===========================================================================
  334. /**
  335. * Thermal Protection protects your printer from damage and fire if a
  336. * thermistor falls out or temperature sensors fail in any way.
  337. *
  338. * The issue: If a thermistor falls out or a temperature sensor fails,
  339. * Marlin can no longer sense the actual temperature. Since a disconnected
  340. * thermistor reads as a low temperature, the firmware will keep the heater on.
  341. *
  342. * If you get "Thermal Runaway" or "Heating failed" errors the
  343. * details can be tuned in Configuration_adv.h
  344. */
  345. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  346. #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
  347. //===========================================================================
  348. //============================= Mechanical Settings =========================
  349. //===========================================================================
  350. // @section machine
  351. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  352. // either in the usual order or reversed
  353. //#define COREXY
  354. //#define COREXZ
  355. //#define COREYZ
  356. //#define COREYX
  357. //#define COREZX
  358. //#define COREZY
  359. // Enable this option for Toshiba steppers
  360. #define CONFIG_STEPPERS_TOSHIBA
  361. //===========================================================================
  362. //============================== Endstop Settings ===========================
  363. //===========================================================================
  364. // @section homing
  365. // Specify here all the endstop connectors that are connected to any endstop or probe.
  366. // Almost all printers will be using one per axis. Probes will use one or more of the
  367. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  368. #define USE_XMIN_PLUG
  369. #define USE_YMIN_PLUG
  370. #define USE_ZMIN_PLUG
  371. //#define USE_XMAX_PLUG
  372. //#define USE_YMAX_PLUG
  373. //#define USE_ZMAX_PLUG
  374. // coarse Endstop Settings
  375. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  376. #if DISABLED(ENDSTOPPULLUPS)
  377. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  378. //#define ENDSTOPPULLUP_XMAX
  379. //#define ENDSTOPPULLUP_YMAX
  380. //#define ENDSTOPPULLUP_ZMAX
  381. //#define ENDSTOPPULLUP_XMIN
  382. //#define ENDSTOPPULLUP_YMIN
  383. //#define ENDSTOPPULLUP_ZMIN
  384. //#define ENDSTOPPULLUP_ZMIN_PROBE
  385. #endif
  386. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  387. #define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  388. #define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  389. #define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  390. #define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  391. #define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  392. #define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
  393. #define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
  394. // Enable this feature if all enabled endstop pins are interrupt-capable.
  395. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  396. //#define ENDSTOP_INTERRUPTS_FEATURE
  397. //=============================================================================
  398. //============================== Movement Settings ============================
  399. //=============================================================================
  400. // @section motion
  401. /**
  402. * Default Settings
  403. *
  404. * These settings can be reset by M502
  405. *
  406. * You can set distinct factors for each E stepper, if needed.
  407. * If fewer factors are given, the last will apply to the rest.
  408. *
  409. * Note that if EEPROM is enabled, saved values will override these.
  410. */
  411. /**
  412. * Default Axis Steps Per Unit (steps/mm)
  413. * Override with M92
  414. * X, Y, Z, E0 [, E1[, E2[, E3]]]
  415. */
  416. #define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 600 } // David TVRR
  417. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 79.87, 79.87, 2566, 563.78 } // Al's TVRR
  418. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 81.26, 80.01, 2561, 599.14 } // Michel TVRR old
  419. //#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 739.65 } // Michel TVRR
  420. /**
  421. * Default Max Feed Rate (mm/s)
  422. * Override with M203
  423. * X, Y, Z, E0 [, E1[, E2[, E3]]]
  424. */
  425. #define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 45 } // David TVRR
  426. /**
  427. * Default Max Acceleration (change/s) change = mm/s
  428. * (Maximum start speed for accelerated moves)
  429. * Override with M201
  430. * X, Y, Z, E0 [, E1[, E2[, E3]]]
  431. */
  432. #define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
  433. /* MICHEL: This has an impact on the "ripples" in print walls */
  434. /**
  435. * Default Acceleration (change/s) change = mm/s
  436. * Override with M204
  437. *
  438. * M204 P Acceleration
  439. * M204 R Retract Acceleration
  440. * M204 T Travel Acceleration
  441. */
  442. #define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
  443. #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
  444. #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves
  445. /**
  446. * Default Jerk (mm/s)
  447. * Override with M205 X Y Z E
  448. *
  449. * "Jerk" specifies the minimum speed change that requires acceleration.
  450. * When changing speed and direction, if the difference is less than the
  451. * value set here, it may happen instantaneously.
  452. */
  453. #define DEFAULT_XJERK 20.0
  454. #define DEFAULT_YJERK 20.0
  455. #define DEFAULT_ZJERK 0.4
  456. #define DEFAULT_EJERK 5.0
  457. //===========================================================================
  458. //============================= Z Probe Options =============================
  459. //===========================================================================
  460. // @section probes
  461. //
  462. // Probe Type
  463. // Probes are sensors/switches that are activated / deactivated before/after use.
  464. //
  465. // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  466. // You must activate one of these to use Auto Bed Leveling below.
  467. //
  468. // Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
  469. //
  470. // A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  471. // For example an inductive probe, or a setup that uses the nozzle to probe.
  472. // An inductive probe must be deactivated to go below
  473. // its trigger-point if hardware endstops are active.
  474. //#define FIX_MOUNTED_PROBE
  475. // The BLTouch probe emulates a servo probe.
  476. // The default connector is SERVO 0. Set Z_ENDSTOP_SERVO_NR below to override.
  477. //#define BLTOUCH
  478. // Z Servo Probe, such as an endstop switch on a rotating arm.
  479. //#define Z_ENDSTOP_SERVO_NR 0
  480. //#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
  481. // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
  482. //#define Z_PROBE_SLED
  483. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  484. // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  485. // X and Y offsets must be integers.
  486. //
  487. // In the following example the X and Y offsets are both positive:
  488. // #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  489. // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  490. //
  491. // +-- BACK ---+
  492. // | |
  493. // L | (+) P | R <-- probe (20,20)
  494. // E | | I
  495. // F | (-) N (+) | G <-- nozzle (10,10)
  496. // T | | H
  497. // | (-) | T
  498. // | |
  499. // O-- FRONT --+
  500. // (0,0)
  501. #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
  502. #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
  503. #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
  504. // X and Y axis travel speed (mm/m) between probes
  505. #define XY_PROBE_SPEED 8000
  506. // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
  507. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  508. // Speed for the "accurate" probe of each point
  509. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  510. // Use double touch for probing
  511. //#define PROBE_DOUBLE_TOUCH
  512. //
  513. // Allen Key Probe is defined in the Delta example configurations.
  514. //
  515. // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
  516. //
  517. // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
  518. // Example: To park the head outside the bed area when homing with G28.
  519. //
  520. // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
  521. //
  522. // For a servo-based Z probe, just set Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES above.
  523. //
  524. // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
  525. // - Use 5V for powered (usu. inductive) sensors.
  526. // - Otherwise connect:
  527. // - normally-closed switches to GND and D32.
  528. // - normally-open switches to 5V and D32.
  529. //
  530. // Normally-closed switches are advised and are the default.
  531. //
  532. //
  533. // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
  534. // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
  535. // default pin for all RAMPS-based boards. Most boards use the X_MAX_PIN by default.
  536. // To use a different pin you can override it here.
  537. //
  538. // WARNING:
  539. // Setting the wrong pin may have unexpected and potentially disastrous consequences.
  540. // Use with caution and do your homework.
  541. //
  542. //#define Z_MIN_PROBE_PIN X_MAX_PIN
  543. //
  544. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
  545. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
  546. //
  547. //#define Z_MIN_PROBE_ENDSTOP
  548. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
  549. // The Z_MIN_PIN will then be used for both Z-homing and probing.
  550. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  551. // To use a probe you must enable one of the two options above!
  552. // Enable Z Probe Repeatability test to see how accurate your probe is
  553. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  554. /**
  555. * Z probes require clearance when deploying, stowing, and moving between
  556. * probe points to avoid hitting the bed and other hardware.
  557. * Servo-mounted probes require extra space for the arm to rotate.
  558. * Inductive probes need space to keep from triggering early.
  559. *
  560. * Use these settings to specify the distance (mm) to raise the probe (or
  561. * lower the bed). The values set here apply over and above any (negative)
  562. * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  563. * Only integer values >= 1 are valid here.
  564. *
  565. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
  566. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
  567. */
  568. #define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
  569. #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
  570. //
  571. // For M851 give a range for adjusting the Z probe offset
  572. //
  573. #define Z_PROBE_OFFSET_RANGE_MIN -20
  574. #define Z_PROBE_OFFSET_RANGE_MAX 20
  575. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  576. // :{ 0:'Low', 1:'High' }
  577. #define X_ENABLE_ON 1
  578. #define Y_ENABLE_ON 1
  579. #define Z_ENABLE_ON 1
  580. #define E_ENABLE_ON 1 // For all extruders
  581. // Disables axis stepper immediately when it's not being used.
  582. // WARNING: When motors turn off there is a chance of losing position accuracy!
  583. #define DISABLE_X false
  584. #define DISABLE_Y false
  585. #define DISABLE_Z false
  586. // Warn on display about possibly reduced accuracy
  587. //#define DISABLE_REDUCED_ACCURACY_WARNING
  588. // @section extruder
  589. #define DISABLE_E false // For all extruders
  590. #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
  591. // @section machine
  592. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  593. #define INVERT_X_DIR false
  594. #define INVERT_Y_DIR false
  595. #define INVERT_Z_DIR true
  596. // @section extruder
  597. // For direct drive extruder v9 set to true, for geared extruder set to false.
  598. #define INVERT_E0_DIR false
  599. #define INVERT_E1_DIR false
  600. #define INVERT_E2_DIR false
  601. #define INVERT_E3_DIR false
  602. // @section homing
  603. //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  604. // Be sure you have this distance over your Z_MAX_POS in case.
  605. // Direction of endstops when homing; 1=MAX, -1=MIN
  606. // :[-1,1]
  607. #define X_HOME_DIR -1
  608. #define Y_HOME_DIR -1
  609. #define Z_HOME_DIR -1
  610. // @section machine
  611. // Travel limits after homing (units are in mm)
  612. #define X_MIN_POS 0
  613. #define Y_MIN_POS 0
  614. #define Z_MIN_POS 0
  615. #define X_MAX_POS 205
  616. #define Y_MAX_POS 205
  617. #define Z_MAX_POS 120
  618. // If enabled, axes won't move below MIN_POS in response to movement commands.
  619. #define MIN_SOFTWARE_ENDSTOPS
  620. // If enabled, axes won't move above MAX_POS in response to movement commands.
  621. #define MAX_SOFTWARE_ENDSTOPS
  622. /**
  623. * Filament Runout Sensor
  624. * A mechanical or opto endstop is used to check for the presence of filament.
  625. *
  626. * RAMPS-based boards use SERVO3_PIN.
  627. * For other boards you may need to define FIL_RUNOUT_PIN.
  628. * By default the firmware assumes HIGH = has filament, LOW = ran out
  629. */
  630. //#define FILAMENT_RUNOUT_SENSOR
  631. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  632. #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  633. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  634. #define FILAMENT_RUNOUT_SCRIPT "M600"
  635. #endif
  636. //===========================================================================
  637. //=============================== Bed Leveling ==============================
  638. //===========================================================================
  639. // @section bedlevel
  640. /**
  641. * Select one form of Auto Bed Leveling below.
  642. *
  643. * If you're also using the Probe for Z Homing, it's
  644. * highly recommended to enable Z_SAFE_HOMING also!
  645. *
  646. * - 3POINT
  647. * Probe 3 arbitrary points on the bed (that aren't collinear)
  648. * You specify the XY coordinates of all 3 points.
  649. * The result is a single tilted plane. Best for a flat bed.
  650. *
  651. * - LINEAR
  652. * Probe several points in a grid.
  653. * You specify the rectangle and the density of sample points.
  654. * The result is a single tilted plane. Best for a flat bed.
  655. *
  656. * - BILINEAR
  657. * Probe several points in a grid.
  658. * You specify the rectangle and the density of sample points.
  659. * The result is a mesh, best for large or uneven beds.
  660. *
  661. * - UBL Unified Bed Leveling
  662. * A comprehensive bed leveling system that combines features and benefits from previous
  663. * bed leveling system. The UBL Bed Leveling System also includes an integrated and easy to use
  664. * Mesh Generation, Mesh Validation and Mesh Editing system.
  665. * - Currently, the UBL Bed Leveling System is only checked out for Cartesian Printers. But with
  666. * that said, it was primarily designed to handle poor quality Delta Printers. If you feel
  667. * adventurous and have a Delta, please post an issue if something doesn't work correctly.
  668. * Initially, you will need to reduce your declared bed size so you have a rectangular area to
  669. * test on.
  670. */
  671. //#define AUTO_BED_LEVELING_3POINT
  672. //#define AUTO_BED_LEVELING_LINEAR
  673. //#define AUTO_BED_LEVELING_BILINEAR
  674. //#define MESH_BED_LEVELING
  675. //#define AUTO_BED_LEVELING_UBL
  676. /**
  677. * Enable detailed logging of G28, G29, M48, etc.
  678. * Turn on with the command 'M111 S32'.
  679. * NOTE: Requires a lot of PROGMEM!
  680. */
  681. //#define DEBUG_LEVELING_FEATURE
  682. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  683. // Gradually reduce leveling correction until a set height is reached,
  684. // at which point movement will be level to the machine's XY plane.
  685. // The height can be set with M420 Z<height>
  686. #define ENABLE_LEVELING_FADE_HEIGHT
  687. #endif
  688. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  689. // Set the number of grid points per dimension.
  690. #define ABL_GRID_MAX_POINTS_X 3
  691. #define ABL_GRID_MAX_POINTS_Y ABL_GRID_MAX_POINTS_X
  692. // Set the boundaries for probing (where the probe can reach).
  693. #define LEFT_PROBE_BED_POSITION 15
  694. #define RIGHT_PROBE_BED_POSITION 170
  695. #define FRONT_PROBE_BED_POSITION 20
  696. #define BACK_PROBE_BED_POSITION 170
  697. // The Z probe minimum outer margin (to validate G29 parameters).
  698. #define MIN_PROBE_EDGE 10
  699. // Probe along the Y axis, advancing X after each column
  700. //#define PROBE_Y_FIRST
  701. #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  702. //
  703. // Experimental Subdivision of the grid by Catmull-Rom method.
  704. // Synthesizes intermediate points to produce a more detailed mesh.
  705. //
  706. //#define ABL_BILINEAR_SUBDIVISION
  707. #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  708. // Number of subdivisions between probe points
  709. #define BILINEAR_SUBDIVISIONS 3
  710. #endif
  711. #endif
  712. #elif ENABLED(AUTO_BED_LEVELING_3POINT)
  713. // 3 arbitrary points to probe.
  714. // A simple cross-product is used to estimate the plane of the bed.
  715. #define ABL_PROBE_PT_1_X 15
  716. #define ABL_PROBE_PT_1_Y 180
  717. #define ABL_PROBE_PT_2_X 15
  718. #define ABL_PROBE_PT_2_Y 20
  719. #define ABL_PROBE_PT_3_X 170
  720. #define ABL_PROBE_PT_3_Y 20
  721. #elif ENABLED(MESH_BED_LEVELING)
  722. //===========================================================================
  723. //=================================== Mesh ==================================
  724. //===========================================================================
  725. #define MANUAL_PROBE_Z_RANGE 4 // Z after Home, bed somewhere below but above 0.0.
  726. #define MESH_INSET 10 // Mesh inset margin on print area
  727. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
  728. #define MESH_NUM_Y_POINTS 3
  729. //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0]
  730. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
  731. #if ENABLED(MANUAL_BED_LEVELING)
  732. #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  733. #endif // MANUAL_BED_LEVELING
  734. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  735. //===========================================================================
  736. //========================= Unified Bed Leveling ============================
  737. //===========================================================================
  738. #define UBL_MESH_INSET 1 // Mesh inset margin on print area
  739. #define UBL_MESH_NUM_X_POINTS 10 // Don't use more than 15 points per axis, implementation limited.
  740. #define UBL_MESH_NUM_Y_POINTS 10
  741. #define UBL_PROBE_PT_1_X 39 // These set the probe locations for when UBL does a 3-Point leveling
  742. #define UBL_PROBE_PT_1_Y 180 // of the mesh.
  743. #define UBL_PROBE_PT_2_X 39
  744. #define UBL_PROBE_PT_2_Y 20
  745. #define UBL_PROBE_PT_3_X 180
  746. #define UBL_PROBE_PT_3_Y 20
  747. #endif // BED_LEVELING
  748. /**
  749. * Commands to execute at the end of G29 probing.
  750. * Useful to retract or move the Z probe out of the way.
  751. */
  752. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  753. // @section homing
  754. // The center of the bed is at (X=0, Y=0)
  755. //#define BED_CENTER_AT_0_0
  756. // Manually set the home position. Leave these undefined for automatic settings.
  757. // For DELTA this is the top-center of the Cartesian print volume.
  758. //#define MANUAL_X_HOME_POS 0
  759. //#define MANUAL_Y_HOME_POS 0
  760. //#define MANUAL_Z_HOME_POS 0
  761. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  762. //
  763. // With this feature enabled:
  764. //
  765. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  766. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  767. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  768. // - Prevent Z homing when the Z probe is outside bed area.
  769. //#define Z_SAFE_HOMING
  770. #if ENABLED(Z_SAFE_HOMING)
  771. #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
  772. #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
  773. #endif
  774. // Homing speeds (mm/m)
  775. #define HOMING_FEEDRATE_XY (50*60)
  776. #define HOMING_FEEDRATE_Z (4*60)
  777. //=============================================================================
  778. //============================= Additional Features ===========================
  779. //=============================================================================
  780. // @section extras
  781. //
  782. // EEPROM
  783. //
  784. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  785. // M500 - stores parameters in EEPROM
  786. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  787. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
  788. //define this to enable EEPROM support
  789. //#define EEPROM_SETTINGS
  790. #if ENABLED(EEPROM_SETTINGS)
  791. // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
  792. #define EEPROM_CHITCHAT // Please keep turned on if you can.
  793. #endif
  794. //
  795. // Host Keepalive
  796. //
  797. // When enabled Marlin will send a busy status message to the host
  798. // every couple of seconds when it can't accept commands.
  799. //
  800. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  801. #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  802. //
  803. // M100 Free Memory Watcher
  804. //
  805. //#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
  806. //
  807. // G20/G21 Inch mode support
  808. //
  809. //#define INCH_MODE_SUPPORT
  810. //
  811. // M149 Set temperature units support
  812. //
  813. //#define TEMPERATURE_UNITS_SUPPORT
  814. // @section temperature
  815. // Preheat Constants
  816. #define PREHEAT_1_TEMP_HOTEND 180
  817. #define PREHEAT_1_TEMP_BED 70
  818. #define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
  819. #define PREHEAT_2_TEMP_HOTEND 240
  820. #define PREHEAT_2_TEMP_BED 100
  821. #define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
  822. //
  823. // Nozzle Park -- EXPERIMENTAL
  824. //
  825. // When enabled allows the user to define a special XYZ position, inside the
  826. // machine's topology, to park the nozzle when idle or when receiving the G27
  827. // command.
  828. //
  829. // The "P" paramenter controls what is the action applied to the Z axis:
  830. // P0: (Default) If current Z-pos is lower than Z-park then the nozzle will
  831. // be raised to reach Z-park height.
  832. //
  833. // P1: No matter the current Z-pos, the nozzle will be raised/lowered to
  834. // reach Z-park height.
  835. //
  836. // P2: The nozzle height will be raised by Z-park amount but never going over
  837. // the machine's limit of Z_MAX_POS.
  838. //
  839. //#define NOZZLE_PARK_FEATURE
  840. #if ENABLED(NOZZLE_PARK_FEATURE)
  841. // Specify a park position as { X, Y, Z }
  842. #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  843. #endif
  844. //
  845. // Clean Nozzle Feature -- EXPERIMENTAL
  846. //
  847. // When enabled allows the user to send G12 to start the nozzle cleaning
  848. // process, the G-Code accepts two parameters:
  849. // "P" for pattern selection
  850. // "S" for defining the number of strokes/repetitions
  851. //
  852. // Available list of patterns:
  853. // P0: This is the default pattern, this process requires a sponge type
  854. // material at a fixed bed location. S defines "strokes" i.e.
  855. // back-and-forth movements between the starting and end points.
  856. //
  857. // P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T"
  858. // defines the number of zig-zag triangles to be done. "S" defines the
  859. // number of strokes aka one back-and-forth movement. Zig-zags will
  860. // be performed in whichever dimension is smallest. As an example,
  861. // sending "G12 P1 S1 T3" will execute:
  862. //
  863. // --
  864. // | (X0, Y1) | /\ /\ /\ | (X1, Y1)
  865. // | | / \ / \ / \ |
  866. // A | | / \ / \ / \ |
  867. // | | / \ / \ / \ |
  868. // | (X0, Y0) | / \/ \/ \ | (X1, Y0)
  869. // -- +--------------------------------+
  870. // |________|_________|_________|
  871. // T1 T2 T3
  872. //
  873. // P2: This starts a circular pattern with circle with middle in
  874. // NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
  875. // Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
  876. //
  877. // Caveats: End point Z should use the same value as Start point Z.
  878. //
  879. // Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
  880. // may change to add new functionality like different wipe patterns.
  881. //
  882. //#define NOZZLE_CLEAN_FEATURE
  883. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  884. // Default number of pattern repetitions
  885. #define NOZZLE_CLEAN_STROKES 12
  886. // Default number of triangles
  887. #define NOZZLE_CLEAN_TRIANGLES 3
  888. // Specify positions as { X, Y, Z }
  889. #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  890. #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
  891. // Circular pattern radius
  892. #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  893. // Circular pattern circle fragments number
  894. #define NOZZLE_CLEAN_CIRCLE_FN 10
  895. // Middle point of circle
  896. #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  897. // Moves the nozzle to the initial position
  898. #define NOZZLE_CLEAN_GOBACK
  899. #endif
  900. //
  901. // Print job timer
  902. //
  903. // Enable this option to automatically start and stop the
  904. // print job timer when M104/M109/M190 commands are received.
  905. // M104 (extruder without wait) - high temp = none, low temp = stop timer
  906. // M109 (extruder with wait) - high temp = start timer, low temp = stop timer
  907. // M190 (bed with wait) - high temp = start timer, low temp = none
  908. //
  909. // In all cases the timer can be started and stopped using
  910. // the following commands:
  911. //
  912. // - M75 - Start the print job timer
  913. // - M76 - Pause the print job timer
  914. // - M77 - Stop the print job timer
  915. #define PRINTJOB_TIMER_AUTOSTART
  916. //
  917. // Print Counter
  918. //
  919. // When enabled Marlin will keep track of some print statistical data such as:
  920. // - Total print jobs
  921. // - Total successful print jobs
  922. // - Total failed print jobs
  923. // - Total time printing
  924. //
  925. // This information can be viewed by the M78 command.
  926. //#define PRINTCOUNTER
  927. //=============================================================================
  928. //============================= LCD and SD support ============================
  929. //=============================================================================
  930. // @section lcd
  931. //
  932. // LCD LANGUAGE
  933. //
  934. // Here you may choose the language used by Marlin on the LCD menus, the following
  935. // list of languages are available:
  936. // en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
  937. // kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test
  938. //
  939. // :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' }
  940. //
  941. //#define LCD_LANGUAGE en
  942. //
  943. // LCD Character Set
  944. //
  945. // Note: This option is NOT applicable to Graphical Displays.
  946. //
  947. // All character-based LCD's provide ASCII plus one of these
  948. // language extensions:
  949. //
  950. // - JAPANESE ... the most common
  951. // - WESTERN ... with more accented characters
  952. // - CYRILLIC ... for the Russian language
  953. //
  954. // To determine the language extension installed on your controller:
  955. //
  956. // - Compile and upload with LCD_LANGUAGE set to 'test'
  957. // - Click the controller to view the LCD menu
  958. // - The LCD will display Japanese, Western, or Cyrillic text
  959. //
  960. // See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
  961. //
  962. // :['JAPANESE', 'WESTERN', 'CYRILLIC']
  963. //
  964. #define DISPLAY_CHARSET_HD44780 JAPANESE
  965. //
  966. // LCD TYPE
  967. //
  968. // You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
  969. // 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
  970. // (ST7565R family). (This option will be set automatically for certain displays.)
  971. //
  972. // IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
  973. // https://github.com/olikraus/U8glib_Arduino
  974. //
  975. //#define ULTRA_LCD // Character based
  976. //#define DOGLCD // Full graphics display
  977. //
  978. // SD CARD
  979. //
  980. // SD Card support is disabled by default. If your controller has an SD slot,
  981. // you must uncomment the following option or it won't work.
  982. //
  983. //#define SDSUPPORT
  984. //
  985. // SD CARD: SPI SPEED
  986. //
  987. // Uncomment ONE of the following items to use a slower SPI transfer
  988. // speed. This is usually required if you're getting volume init errors.
  989. //
  990. //#define SPI_SPEED SPI_HALF_SPEED
  991. //#define SPI_SPEED SPI_QUARTER_SPEED
  992. //#define SPI_SPEED SPI_EIGHTH_SPEED
  993. //
  994. // SD CARD: ENABLE CRC
  995. //
  996. // Use CRC checks and retries on the SD communication.
  997. //
  998. //#define SD_CHECK_AND_RETRY
  999. //
  1000. // ENCODER SETTINGS
  1001. //
  1002. // This option overrides the default number of encoder pulses needed to
  1003. // produce one step. Should be increased for high-resolution encoders.
  1004. //
  1005. //#define ENCODER_PULSES_PER_STEP 1
  1006. //
  1007. // Use this option to override the number of step signals required to
  1008. // move between next/prev menu items.
  1009. //
  1010. //#define ENCODER_STEPS_PER_MENU_ITEM 5
  1011. /**
  1012. * Encoder Direction Options
  1013. *
  1014. * Test your encoder's behavior first with both options disabled.
  1015. *
  1016. * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1017. * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
  1018. * Reversed Value Editing only? Enable BOTH options.
  1019. */
  1020. //
  1021. // This option reverses the encoder direction everywhere
  1022. //
  1023. // Set this option if CLOCKWISE causes values to DECREASE
  1024. //
  1025. //#define REVERSE_ENCODER_DIRECTION
  1026. //
  1027. // This option reverses the encoder direction for navigating LCD menus.
  1028. //
  1029. // If CLOCKWISE normally moves DOWN this makes it go UP.
  1030. // If CLOCKWISE normally moves UP this makes it go DOWN.
  1031. //
  1032. //#define REVERSE_MENU_DIRECTION
  1033. //
  1034. // Individual Axis Homing
  1035. //
  1036. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1037. //
  1038. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1039. //
  1040. // SPEAKER/BUZZER
  1041. //
  1042. // If you have a speaker that can produce tones, enable it here.
  1043. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1044. //
  1045. //#define SPEAKER
  1046. //
  1047. // The duration and frequency for the UI feedback sound.
  1048. // Set these to 0 to disable audio feedback in the LCD menus.
  1049. //
  1050. // Note: Test audio output with the G-Code:
  1051. // M300 S<frequency Hz> P<duration ms>
  1052. //
  1053. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1054. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1055. //
  1056. // CONTROLLER TYPE: Standard
  1057. //
  1058. // Marlin supports a wide variety of controllers.
  1059. // Enable one of the following options to specify your controller.
  1060. //
  1061. //
  1062. // ULTIMAKER Controller.
  1063. //
  1064. //#define ULTIMAKERCONTROLLER
  1065. //
  1066. // ULTIPANEL as seen on Thingiverse.
  1067. //
  1068. //#define ULTIPANEL
  1069. //
  1070. // Cartesio UI
  1071. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1072. //
  1073. //#define CARTESIO_UI
  1074. //
  1075. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1076. // http://reprap.org/wiki/PanelOne
  1077. //
  1078. //#define PANEL_ONE
  1079. //
  1080. // MaKr3d Makr-Panel with graphic controller and SD support.
  1081. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1082. //
  1083. //#define MAKRPANEL
  1084. //
  1085. // ReprapWorld Graphical LCD
  1086. // https://reprapworld.com/?products_details&products_id/1218
  1087. //
  1088. //#define REPRAPWORLD_GRAPHICAL_LCD
  1089. //
  1090. // Activate one of these if you have a Panucatt Devices
  1091. // Viki 2.0 or mini Viki with Graphic LCD
  1092. // http://panucatt.com
  1093. //
  1094. //#define VIKI2
  1095. //#define miniVIKI
  1096. //
  1097. // Adafruit ST7565 Full Graphic Controller.
  1098. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1099. //
  1100. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1101. //
  1102. // RepRapDiscount Smart Controller.
  1103. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1104. //
  1105. // Note: Usually sold with a white PCB.
  1106. //
  1107. //#define REPRAP_DISCOUNT_SMART_CONTROLLER
  1108. //
  1109. // GADGETS3D G3D LCD/SD Controller
  1110. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1111. //
  1112. // Note: Usually sold with a blue PCB.
  1113. //
  1114. //#define G3D_PANEL
  1115. //
  1116. // RepRapDiscount FULL GRAPHIC Smart Controller
  1117. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1118. //
  1119. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1120. //
  1121. // MakerLab Mini Panel with graphic
  1122. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1123. //
  1124. //#define MINIPANEL
  1125. //
  1126. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1127. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1128. //
  1129. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1130. // is pressed, a value of 10.0 means 10mm per click.
  1131. //
  1132. //#define REPRAPWORLD_KEYPAD
  1133. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1134. //
  1135. // RigidBot Panel V1.0
  1136. // http://www.inventapart.com/
  1137. //
  1138. //#define RIGIDBOT_PANEL
  1139. //
  1140. // BQ LCD Smart Controller shipped by
  1141. // default with the BQ Hephestos 2 and Witbox 2.
  1142. //
  1143. //#define BQ_LCD_SMART_CONTROLLER
  1144. //
  1145. // CONTROLLER TYPE: I2C
  1146. //
  1147. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1148. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1149. //
  1150. //
  1151. // Elefu RA Board Control Panel
  1152. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1153. //
  1154. //#define RA_CONTROL_PANEL
  1155. //
  1156. // Sainsmart YW Robot (LCM1602) LCD Display
  1157. //
  1158. //#define LCD_I2C_SAINSMART_YWROBOT
  1159. //
  1160. // Generic LCM1602 LCD adapter
  1161. //
  1162. //#define LCM1602
  1163. //
  1164. // PANELOLU2 LCD with status LEDs,
  1165. // separate encoder and click inputs.
  1166. //
  1167. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1168. // For more info: https://github.com/lincomatic/LiquidTWI2
  1169. //
  1170. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1171. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1172. //
  1173. //#define LCD_I2C_PANELOLU2
  1174. //
  1175. // Panucatt VIKI LCD with status LEDs,
  1176. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1177. //
  1178. //#define LCD_I2C_VIKI
  1179. //
  1180. // SSD1306 OLED full graphics generic display
  1181. //
  1182. //#define U8GLIB_SSD1306
  1183. //
  1184. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1185. //
  1186. //#define SAV_3DGLCD
  1187. #if ENABLED(SAV_3DGLCD)
  1188. //#define U8GLIB_SSD1306
  1189. #define U8GLIB_SH1106
  1190. #endif
  1191. //
  1192. // CONTROLLER TYPE: Shift register panels
  1193. //
  1194. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1195. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1196. //
  1197. //#define SAV_3DLCD
  1198. //=============================================================================
  1199. //=============================== Extra Features ==============================
  1200. //=============================================================================
  1201. // @section extras
  1202. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1203. //#define FAST_PWM_FAN
  1204. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1205. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1206. // is too low, you should also increment SOFT_PWM_SCALE.
  1207. //#define FAN_SOFT_PWM
  1208. // Incrementing this by 1 will double the software PWM frequency,
  1209. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1210. // However, control resolution will be halved for each increment;
  1211. // at zero value, there are 128 effective control positions.
  1212. #define SOFT_PWM_SCALE 0
  1213. // Temperature status LEDs that display the hotend and bed temperature.
  1214. // If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
  1215. // Otherwise the RED led is on. There is 1C hysteresis.
  1216. //#define TEMP_STAT_LEDS
  1217. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  1218. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1219. //#define PHOTOGRAPH_PIN 23
  1220. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1221. //#define SF_ARC_FIX
  1222. // Support for the BariCUDA Paste Extruder.
  1223. //#define BARICUDA
  1224. //define BlinkM/CyzRgb Support
  1225. //#define BLINKM
  1226. // Support for an RGB LED using 3 separate pins with optional PWM
  1227. //#define RGB_LED
  1228. #if ENABLED(RGB_LED)
  1229. #define RGB_LED_R_PIN 34
  1230. #define RGB_LED_G_PIN 43
  1231. #define RGB_LED_B_PIN 35
  1232. #endif
  1233. /*********************************************************************\
  1234. * R/C SERVO support
  1235. * Sponsored by TrinityLabs, Reworked by codexmas
  1236. **********************************************************************/
  1237. // Number of servos
  1238. //
  1239. // If you select a configuration below, this will receive a default value and does not need to be set manually
  1240. // set it manually if you have more servos than extruders and wish to manually control some
  1241. // leaving it undefined or defining as 0 will disable the servo subsystem
  1242. // If unsure, leave commented / disabled
  1243. //
  1244. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  1245. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1246. // 300ms is a good value but you can try less delay.
  1247. // If the servo can't reach the requested position, increase it.
  1248. #define SERVO_DELAY 300
  1249. // Servo deactivation
  1250. //
  1251. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1252. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1253. /**********************************************************************\
  1254. * Support for a filament diameter sensor
  1255. * Also allows adjustment of diameter at print time (vs at slicing)
  1256. * Single extruder only at this point (extruder 0)
  1257. *
  1258. * Motherboards
  1259. * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
  1260. * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
  1261. * 301 - Rambo - uses Analog input 3
  1262. * Note may require analog pins to be defined for different motherboards
  1263. **********************************************************************/
  1264. // Uncomment below to enable
  1265. //#define FILAMENT_WIDTH_SENSOR
  1266. #define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
  1267. #if ENABLED(FILAMENT_WIDTH_SENSOR)
  1268. #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
  1269. #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
  1270. #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
  1271. #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
  1272. #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
  1273. #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
  1274. //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
  1275. //#define FILAMENT_LCD_DISPLAY
  1276. #endif
  1277. #endif // CONFIGURATION_H