* Fix M48 for Delta's  There was a scope issue: DELTA_PROBEABLE_RADIUS wasn't getting defined.

* Check if the specified G29 command requires homing

Things should be pretty stable for a while.   
But it wouldn't surprise me if the Delta people have a need for a few special commands.

Since we already used 'T' for `G29` Topology Report in the past, and since 'T' is available…

Also clean up ubl_motion.cpp debug info and fix declaration of cx & cy

UBL on Delta's....     Should be close!    Should not affect any Cartesian printer.

- allow H code value to override probing height
- minor cleanups

- Split M421 into separate versions for bilinear and ubl
- Fix minor issue in G26

* M421 Mesh Point Offset and misc. UBL clean up

Allow M421 to accept an offset as well as absolute value for a specified
mesh point.
And misc. UBL clean up to reduce redundent code.

* Better error checking for M421

* Fix M421 Y index bug

I just noticed....  We've had a Y index bug for who knows how long?

    /**
     * UBL System submenu
     *
     *  Prepare
     * - Unified Bed Leveling
     *   - Activate UBL
     *   - Deactivate UBL
     *   - Mesh Storage
     *       Memory Slot:
     *       Load Bed Mesh
     *       Save Bed Mesh
     *   - Output Map
     *       Map Type:
     *       Output Bed Mesh Host / Output Bed Mesh CSV
     *   - UBL Tools
     *     - Build Mesh
     *         Build PLA Mesh
     *         Build ABS Mesh
     *       - Build Custom Mesh
     *           Hotend Temp:
     *           Bed Temp:
     *           Build Custom Mesh
     *         Info Screen
     *       - Build Cold Mesh
     *       - Fill-in Mesh
     *           Fill-in Mesh
     *           Smart Fill-in
     *           Manual Fill-in
     *           Info Screen
     *         Continue Bed Mesh
     *         Invalidate All
     *         Invalidate Closest
     *     - Validate Mesh
     *         PLA Mesh Validation
     *         ABS Mesh Validation
     *       - Custom Mesh Validation
     *           Hotend Temp:
     *           Bed Temp:
     *           Validate Mesh
     *         Info Screen
     *     - Edit Mesh
     *         Fine Tune All
     *         Fine Tune Closest
     *       - Adjust Mesh Height
     *           Height Amount:
     *           Adjust Mesh Height
     *         Info Screen
     *     - Mesh Leveling
     *         3-Point Mesh Leveling
     *       - Grid Mesh Leveling
     *           Side points:
     *           Level Mesh
     *         Info Screen
     *   - Output UBL Info
     */

UBL Clean up.

add BLTouch-related messages in english and (rusty) french;
add missing endstops.h in ultralcd.cpp;
fix misc. compiler warnings;
fix lsf_reset - ZERO macro can't handle a pointer as it would only memset the size of the pointer, not the size of the entire struct

Also...   The memory corruption issue may be fixed.   The GCC compiler
was inlining static functions and this caused the G29() stack frame to
become much larger than the AVR could handle.

* relocated ubl state to config. store:
 * removed a number of ubl state variables and padding which were largely unused - saved 58 bytes of both SRAM and EEPROM;
 * modified ubl sanity_check - no longer checks removed state variables that were otherwise unused, where checking didn't seem to accomplish anything, ultimately;
 * removed pre_initialized state, saving 64 bytes of SRAM;
 * removed automatic saving of UBL state after UBL activation/deactivation;
* consolidated multiple GRID_MAX_POINTS_X/Y to 'Global Leveling' section of EEPROM;
* minor update to G29 Sx notes/instructions;
* renamed mesh load and save parameter to 'slot' from 'm' for clarity;

fix maximum mesh_index_ array size at 16 (15+1);

https://github.com/MarlinFirmware/Marlin/commit/5e9726530f
ac1b9437c2

This data corruption problem is very difficult.  Just changing the code
a little bit changes whether the problem even happens and what is
affected.  I need these changes in the main branch so I can operate with
the extra debug code always available and turned on.

Everything is setup such that if M100 is turned off or DEBUG(ECHO) is
turned off, the code is not affected.   M100 has been made a little bit
more inteligent so it can display the serial command buffers in a more
meaningful way (because the data corruption seems to often times end up
in that area).

Configuration_store.cpp - changed a couple of print statements so the
values were printed.  The old method resulted in the formula being
printed.

ubl_G29
1) added support for R option to P4.  Now probes all points unless R is
present and the number is greater than 0.

2) P2 - moved map print statement so it showed the point that was
currently being probed,  The old location did this only for the first
point.

3) P4 - Moved the map print for the same reason.

ultralcd.cpp - changed "Mesh Editor :" to "Mesh Editor" because the LCD
draw routine puts a ":" in automatically so you end up with an extra ":"
using the old message.

Having these items randomly (and errorniously) disappear cost me several
hours of work yesterday.