This is what I did yesterday:

- basicly gave the tests more comprehensive names; put all the
declarations at the top; got rid of the magic negative C-value (renamed
to P + A, O, T)

- "cos(RADIANS(180 + 30 * axis)) * (1 + circles * 0.1 * ((zig_zag) ? 1 :
-1)) * delta_calibration_radius" compiles wrong is zig_zag statement is
without brackets

- DELTA_TOWER_ANGLE_TRIM reset to 3 values (the calcs use the 3th value
to normalize will not compile otherwise)

-Wrote 3 dummies to keep EEPROM lenght the same

-Reset the configs to the 'original' with autocal + menu disabled (but
can be enabled of course)

The Configuration.h file entries for BL-Touch have been updated to:
```cpp
//#define BLTOUCH
//#define BLTOUCH_DELAY 375      // (ms) Enable and increase if needed
//#define BLTOUCH_HEATERS_OFF // if defined the printer's heaters are
turned off during probe event
```

Also setting up Z-Probe on the machine.

Change to support new name GRID_MAX_POINTS_XY
Start UBL at version 1.0 in the CUSTOM_MACHINE_NAME

These are my two 'Nice' machines.  Both are good example machines.  The
FolgerTech i3-2020 is probably the best value kit on the market right
now.  And it has developed a 'Cult Following' of hobbiests.  I'll always
have an up to date Configuration.h file set for it, so it may as well be
an example configuration.

And the gCreate gMax 1.5+ is the best printer I've ever seen that runs
Marlin.  For sure, I'll always have up to the minute Configuration.h
files for this printer also.   I've moved over to using the gMax as my
primary development machine for Marlin.   So...  Besides being a good
machine, it is a nice convienience for me to have this Configuration.h
file as an 'Example'.

More consistent with M665 where C-value is allowed as well, then
normalized

and getting rid off verbose level 3 and configuration_adv settings

- Making M665 compatible with repetier (see
http://reprap.org/wiki/G_code#M665:_Set_delta_configuration)

- M665 B also sets the radius for manual calibration menu

- Converting tower ajustment definitions to arrays - tower angle
corrections compatible with Esher 3D wizzard

- Only tower angles need to be adjustable with M665 and stored to EEPROM
- tower radius and diag rod can be adjusted in the FW only with #define

Firmware was forgetting the z_fade_height in Planner, set by M420 Z<f>,
after each reset or loading settings from EEPROM. Added the float
z_fade_height to EEPROM-Storage, now remembers the value.

DAC_STEPPER_DFLT wasn't changed to DAC_MOTOR_CURRENT_DEFAULT in all
places on PR #6124

# This is the 1st commit message:

MCP4728 consistency & fix ultralcd.cpp

The MCP4728 DAC controls the stepper motor current strenth on the
PRINTRBOARD Rev F and RIGIDBOARD V2 boards.

PR #5792 on 9 FEB 2017 implemented default drive percentages but only on
the RIGIDBOARD V2.

This change moves the default settings to Configuration_adv.h.

Also, ultralcd.cpp won't compile because of a type def conflict.
Changed it to match the one in stepper_dac.cpp

===========================================================

reword stepper curent section for clarity

===========================================================

change name & improve comments

===========================================================

changed name from A4JP to SCOOVO_X9H per PR #6139

# This is the commit message #2:

fix typo

==============================================

clarified BLTouch calculation & changed comment delimitters/flags

I found it hard to pickout the various sections in this area so I
changed most comments from // style to /** ... */

Made the BLTouch calculation simpler and clarified the units of measure
for the result.

============================================

add changes to example configurations

============================================

add TinyBoy2 to this PR & add BLTouch Delay

The offset for Z_DUAL_ENDSTOP (z_endstop_adj) is already in Marlin.
This PR just makes it a configuration item.

z_endstop_adj is initialized in two places so both had to be modified.