- fix broken `M421` due to less-than-careful optimization
- add HOME_AFTER_DEACTIVATE define to advanced config so not everyone has to rehome after steppers are deactivated
- misc. cleanups (remove unused label, unused variables)

* Fix M48 for Delta's  There was a scope issue: DELTA_PROBEABLE_RADIUS wasn't getting defined.

* Check if the specified G29 command requires homing

Update the gMax files to display better with Proportional Fonts

UltiPanel was enabled, but technically, it is a REPRAP_DISCOUNT_SMART_CONTROLLER
Either configuration works on the machine.  But we want it 'Right'.

Setup the Proportional Font spacing so columns line up nicer on PronterFace and Repetier Host.

- update example configs

I think I forgot to Sync before I committed last time.   Some UBL
changes did not stick.

Also, update the gMax configuaration.h file so other than unique numbers
and settings, it exactly matches the default configuration.h file.

 - rename to PROBING_HEATERS_OFF
 - move heater pausing functionality into thermalManager
   - add variables, pause(), ispaused(), other functions
 - add fan pausing functionality -> PROBING_FANS_OFF
 - add probing_pause() wrapper
 - move pausing into do_homing_move() and do_probe_move() to minimize quiet time and so other probe types can benefit
 - example configs

This is what I did yesterday:

- basicly gave the tests more comprehensive names; put all the
declarations at the top; got rid of the magic negative C-value (renamed
to P + A, O, T)

- "cos(RADIANS(180 + 30 * axis)) * (1 + circles * 0.1 * ((zig_zag) ? 1 :
-1)) * delta_calibration_radius" compiles wrong is zig_zag statement is
without brackets

- DELTA_TOWER_ANGLE_TRIM reset to 3 values (the calcs use the 3th value
to normalize will not compile otherwise)

-Wrote 3 dummies to keep EEPROM lenght the same

-Reset the configs to the 'original' with autocal + menu disabled (but
can be enabled of course)

The Configuration.h file entries for BL-Touch have been updated to:
```cpp
//#define BLTOUCH
//#define BLTOUCH_DELAY 375      // (ms) Enable and increase if needed
//#define BLTOUCH_HEATERS_OFF // if defined the printer's heaters are
turned off during probe event
```

Also setting up Z-Probe on the machine.

Change to support new name GRID_MAX_POINTS_XY
Start UBL at version 1.0 in the CUSTOM_MACHINE_NAME

These are my two 'Nice' machines.  Both are good example machines.  The
FolgerTech i3-2020 is probably the best value kit on the market right
now.  And it has developed a 'Cult Following' of hobbiests.  I'll always
have an up to date Configuration.h file set for it, so it may as well be
an example configuration.

And the gCreate gMax 1.5+ is the best printer I've ever seen that runs
Marlin.  For sure, I'll always have up to the minute Configuration.h
files for this printer also.   I've moved over to using the gMax as my
primary development machine for Marlin.   So...  Besides being a good
machine, it is a nice convienience for me to have this Configuration.h
file as an 'Example'.

More consistent with M665 where C-value is allowed as well, then
normalized

and getting rid off verbose level 3 and configuration_adv settings

- Making M665 compatible with repetier (see
http://reprap.org/wiki/G_code#M665:_Set_delta_configuration)

- M665 B also sets the radius for manual calibration menu

- Converting tower ajustment definitions to arrays - tower angle
corrections compatible with Esher 3D wizzard

- Only tower angles need to be adjustable with M665 and stored to EEPROM
- tower radius and diag rod can be adjusted in the FW only with #define